If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the lock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for front passenger side electrical key antenna)).
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Door Trigger Switch | Front door outside handle assembly (for front passenger side) (unlock sensor) / OFF or ON | OFF: Front door outside handle assembly (for passenger side) (unlock sensor) not touched
ON: Front door outside handle assembly (for passenger side) (unlock sensor) touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
On the GTS screen, the display changes between ON and OFF as shown in the table above.
OK
NG
Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.
Disconnect the F5*1 or E1*2 front door outside handle assembly (for driver side door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-8 (TSW2) - F5-1 (TRG+) | Always | Below 1 Ω |
| D48-11 (GND) - Body ground | Always | Below 1 Ω |
| D41-8 (TSW2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-8 (TSW2) - E1-1 (TRG+) | Always | Below 1 Ω |
| D48-11 (GND) - Body ground | Always | Below 1 Ω |
| D41-8 (TSW2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.
Reconnect the F5*1 or E1*2 front door outside handle assembly connector.
*1: for LHD
*2: for RHD
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
*b | Waveform |
| *c | Passenger side door lock sensor touched | - | - |
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| D41-8 (TSW2) - D48-11 (GND) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Passenger side door lock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
OK
NG