Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (front passenger side electrical key antenna) at intervals of 250 ms. For the certification ECU (smart key ECU assembly) to detect when the key is brought close to the vehicle, a signal requesting a response from the key is transmitted within approximately 1 m (3.28 ft.) of the front passenger side door at intervals of 250 ms. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (front passenger side electrical key antenna) (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A2 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (CLG2 - ANT1, CG2B - ANT2) (1 trip detection logic*1).
·

Wire harness or connector

·

Front door outside handle assembly (for front passenger side door)

·

Certification ECU (smart key ECU assembly)


Any time*2

*1: Only output while a malfunction is present.

*2: Only when the vehicle is stopped.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger side door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267E89
1.26,1.021 1.635,1.188 0.375,0.167 10 false ANT1 1.26,1.438 1.635,1.604 0.375,0.167 10 false ANT2 5.531,1 5.917,1.167 0.385,0.167 10 false CLG2 5.542,1.885 5.896,2.052 0.354,0.167 10 false GND 5.219,1 5.49,1.167 0.271,0.167 10 false D41 5.531,1.438 5.948,1.615 0.417,0.177 10 false CG2B 5.208,1.438 5.479,1.604 0.271,0.167 10 false D41 5.208,1.875 5.458,2.031 0.25,0.156 10 false D48 5.25,0.813 5.427,0.99 0.177,0.177 10 false 11 5.25,1.25 5.427,1.417 0.177,0.167 10 false 10 5.25,1.688 5.417,1.854 0.167,0.167 10 false 11 1.729,0.875 1.865,1.052 0.135,0.177 10 false 6 1.74,1.323 1.885,1.5 0.146,0.177 10 false 3 0.438,2.406 0.781,2.563 0.344,0.156 10 false F5*1 0.438,2.583 2.76,2.927 2.323,0.344 10 false Front Door Outside Handle Assembly (for Passenger Side Door) 5.198,2.417 6.719,2.771 1.521,0.354 10 false Certification ECU (Smart Key ECU Assembly) 0.823,2.406 1.167,2.563 0.344,0.156 10 false E1*2 0.146,3.396 0.865,3.573 0.719,0.177 10 false *1: for LHD 0.948,3.385 1.667,3.563 0.719,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a LIN communication system and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

·

Front door outside handle assembly (for passenger side door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly.

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F5*1 or E1*2 front door outside handle assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
D41-11 (CLG2) - F5-6 (ANT1) Always Below 1 Ω
D41-10 (CG2B) - F5-3 (ANT2) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D41-11 (CLG2) - Body ground Always 10 kΩ or higher
D41-10 (CG2B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
D41-11 (CLG2) - E1-6 (ANT1) Always Below 1 Ω
D41-10 (CG2B) - E1-3 (ANT2) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D41-11 (CLG2) - Body ground Always 10 kΩ or higher
D41-10 (CG2B) - Body ground Always 10 kΩ or higher




OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA)
U190203E01
0.195,0.147 0.416,0.347 0.221,0.200 10 *a 1.204,2.823 1.425,3.023 0.221,0.200 10 *b 0.966,3.636 1.326,3.801 0.360,0.165 10 GND 3.852,3.636 4.212,3.801 0.360,0.165 10 GND 4.146,2.823 4.367,3.023 0.221,0.200 10 *c 2.358,1.982 2.745,2.146 0.387,0.163 10 GND 5.258,1.982 5.660,2.146 0.401,0.163 10 CG2B 4.679,1.982 5.080,2.146 0.401,0.163 10 CLG2 2.19,0.632 2.496,0.795 0.306,0.163 10 D48 4.809,0.632 5.099,0.795 0.289,0.163 10 D41 5.1,1.406 4.882,1.964 false 2.707,1.517 2.532,1.964 false 5.178,1.406 5.396,1.964 false

Text in Illustration
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Waveform 1
*c Waveform 2 - -

a.

Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F5*1 or E1*2 front door outside handle assembly connector.

*1: for LHD

*2: for RHD



c.

Using an oscilloscope, check the waveform.

HINT:

Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).


OK:
Tester Connection Switch Condition Tool Setting Specified Condition
D41-11 (CLG2) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter not inside vehicle

5.

Electrical key transmitter brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
D41-11 (CLG2) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter not inside vehicle

5.

Electrical key transmitter brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
D41-10 (CG2B) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked with electrical key transmitter sub-assembly


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)
a.

Temporarily replace the front door outside handle assembly with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)