Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a circuit malfunction is detected in the engine start permission signal output circuit inside the certification ECU (smart key ECU assembly), or when an abnormal external engine start permission signal is detected.

HINT:

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2275
·

Circuit malfunction detected in the engine start permission output circuit inside the certification ECU (smart key ECU assembly) (1-trip detection logic*).

·

External engine start permission signal malfunction (1-trip detection logic*).


·

Certification ECU (smart key ECU assembly)

·

SFI system

·

Wire harness or connector


Engine start operation is performed.

*: Only output while a malfunction is present and the engine switch is on (IG)


Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2275 - -

WIRING DIAGRAM

B312733E02
4.99,1.365 5.188,1.51 0.198,0.146 10 false 11 4.833,1.958 5.115,2.135 0.281,0.177 10 false D48 5.24,1.448 5.552,1.604 0.313,0.156 10 false GND 4.802,2.125 6.323,2.49 1.521,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.802,0.844 2.229,1 0.427,0.156 10 false STSW 5.25,0.854 5.667,1 0.417,0.146 10 false STSW 1.594,1.5 1.938,1.667 0.344,0.167 10 false ECM 2.281,0.729 2.469,0.885 0.188,0.156 10 false 17 5.052,0.74 5.167,0.896 0.115,0.156 10 false 7 1.594,1.333 1.875,1.49 0.281,0.156 10 false A33

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ECM)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A33 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Condition Connection Specified Condition
D48-7 (STSW) - A33-17 (STSW) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D48-7 (STSW) - Body ground Always 10 kΩ or higher




OK

2.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the A33 ECM connector.


c.
U190197E01
0.2,0.129 0.385,0.290 0.186,0.161 10 *a 2.132,1.767 2.486,1.923 0.353,0.156 10 GND 2.069,1.206 2.283,1.746 false 1.017,1.775 1.473,1.931 0.457,0.156 10 STSW 1.523,0.285 1.818,0.441 0.295,0.156 10 D48 1.567,1.082 1.31,1.754 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Connection Specified Condition
D48-7 (STSW) - D48-11 (GND) With the brake pedal*1 or clutch pedal*2 depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off) 2 V or less → 9 V or higher


*1: for Automatic Transmission

*2: for Manual Transmission


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)