*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
If the display indicates a communication fault in the GTS, inspect the DLC3.
When any CAN communication system DTCs are output, perform troubleshooting on the CAN communication system first.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs (Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR) and freeze frame data (Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Record or print DTCs and freeze frame data if necessary.
| Proceed to |
|---|
| NEXT |
NEXT
Clear DTCs and freeze frame data.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Switch the ECM from normal mode to check mode.
Refer to Check Mode Procedure.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Confirm problem symptoms.
If the engine does not start, first perform the "Check DTC" procedure and "Conduct Basic Inspection" procedure below.
| Result | Proceed to |
|---|---|
| Malfunction does not occur | A |
| Malfunction occurs | B |
A
B
Refer to Symptom Simulation.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Refer to DTC Check / Clear.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Trouble code | A |
| No trouble code output | B |
A
B
Refer to Diagnostic Trouble Code Chart.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT
Conduct basic inspection.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>BASIC INSPECTION
| Result | Proceed to |
|---|---|
| Malfunctioning parts not confirmed | A |
| Malfunctioning parts confirmed | B |
A
B
Refer to Problem Symptoms Table.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Malfunctioning circuit confirmed | A |
| Malfunctioning parts confirmed | B |
A
B
Check the ECM power source circuit.
Refer to ECM Power Source Circuit.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit
| Proceed to |
|---|
| NEXT |
NEXT
| Result | Proceed to |
|---|---|
| Malfunction not confirmed | A |
| Malfunction confirmed | B |
A
B
Check for intermittent problems.
Refer to Check for Intermittent Problems.
Click hereEngine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT