Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297682 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B314076E02
0.625,3.396 2.313,3.594 1.688,0.198 10 false : CAN Communication Line 3.167,2.063 4.76,2.406 1.594,0.344 10 false Main Body ECU (Network Gateway ECU) 2.188,2.906 4.844,3.083 2.656,0.177 10 false Instrument Panel Junction Block Assembly 2.177,2.75 2.375,2.906 0.198,0.156 10 false 3B 5.354,1.74 6.917,2.115 1.563,0.375 10 false Certification ECU (Smart Key ECU Assembly) 0.49,1.854 1.719,2.229 1.229,0.375 10 false Combination Meter Assembly 0.49,1.656 0.708,1.813 0.219,0.156 10 false D7 2.177,1.042 2.375,1.198 0.198,0.156 10 false 22 3.781,1.031 3.979,1.188 0.198,0.156 10 false 27 1.531,1.01 1.729,1.167 0.198,0.156 10 false 18 0.448,1.042 0.646,1.198 0.198,0.156 10 false 40 3.167,1.885 3.427,2.042 0.26,0.156 10 false MB 4.063,1.135 4.313,1.292 0.25,0.156 10 false ILL 0.708,1.146 1.021,1.302 0.313,0.156 10 false ES2 1.146,1.146 1.479,1.302 0.333,0.156 10 false ILL+

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.


PROCEDURE

2.READ VALUE USING GTS (IMMOBILISER)
a.

Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset Set: Engine immobiliser set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser unset (engine start permitted) [engine switch on (ACC) or on (IG)]
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the certification ECU (smart key ECU assembly).

OK:

"Set" appears on screen.




OK

3.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Check that the security indicator light illuminates when operating it with the Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -

OK:

Security indicator light can be turned on and off using GTS.




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - COMBINATION METER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - COMBINATION METER ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the D7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-22 - D7-18 Always Below 1 Ω
D7-40 - Body ground Always Below 1 Ω
3B-22 - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U190237E01
0.114,0.061 0.300,0.222 0.186,0.161 10 *a 2.219,0.427 2.462,0.583 0.243,0.156 10 MB 5.651,0.22 5.869,0.376 0.218,0.156 10 3B 3.469,0.94 3.528,1.175 false 3.447,1.19 3.689,1.346 0.243,0.156 10 ILL

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
MB-27 (ILL) - 3B-22 Always Below 1 Ω



OK

6.REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

When the immobiliser is set, check that the security indicator light blinks.


OK:

Security indicator light blinks.



OK

END

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)