Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297683 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power for main body ECU (network gateway ECU) operation.

WIRING DIAGRAM

B316997E02
3.49,2.188 5.073,2.563 1.583,0.375 10 false Instrument Panel Junction Block Assembly 4.823,2.906 6.427,3.281 1.604,0.375 10 false Main Body ECU (Network Gateway ECU) 2.854,1.292 3.344,1.448 0.49,0.156 10 false MPX-B 2.865,0.854 3.354,1.01 0.49,0.156 10 false ECU-B 2.208,0.854 2.563,1.01 0.354,0.156 10 false DCC 0.271,0.729 1.323,0.927 1.052,0.198 10 false from MAIN Fuse 4.885,1.156 5.125,1.302 0.24,0.146 10 false MB 4.885,0.719 5.125,0.865 0.24,0.146 10 false MB 4.896,0.958 5.083,1.104 0.188,0.146 10 false 32 4.938,0.49 5.042,0.635 0.104,0.146 10 false 1 3.677,1.146 3.885,1.292 0.208,0.146 10 false 3C 3.677,0.969 3.865,1.115 0.188,0.146 10 false 19 3.677,0.708 3.885,0.854 0.208,0.146 10 false 3A 3.688,0.51 3.875,0.656 0.188,0.146 10 false 27 6.229,1.625 6.448,1.771 0.219,0.146 10 false D6 6.26,0.948 6.365,1.094 0.104,0.146 10 false 4 6.271,1.417 6.375,1.563 0.104,0.146 10 false 1 6.198,1.167 6.479,1.313 0.281,0.146 10 false A73 4.875,1.688 5.115,1.833 0.24,0.146 10 false MB 4.885,1.49 5.073,1.635 0.188,0.146 10 false 11 3.688,1.677 3.896,1.823 0.208,0.146 10 false 3B 3.688,1.49 3.875,1.635 0.188,0.146 10 false 18 5.208,0.719 5.625,0.885 0.417,0.167 10 false BECU 5.219,1.146 5.667,1.313 0.448,0.167 10 false BMPX 5.219,1.677 5.563,1.844 0.344,0.167 10 false GND 5.75,1.167 6.094,1.333 0.344,0.167 10 false GND 5.76,1.635 6.104,1.802 0.344,0.167 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A and 3C instrument panel junction block assembly connectors.


b.
U146922E05
0.063,0.063 0.25,0.219 0.188,0.156 10 false *a 1.625,0.24 1.833,0.396 0.208,0.156 10 false 3C 1.635,1.792 1.844,1.948 0.208,0.156 10 false 3A

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-27 - Body ground Always 11 to 14 V
3C-19 - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the A73 and D6 main body ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-18 - Body ground Always Below 1 Ω
A73-4 (GND )- Body ground Always Below 1 Ω
D6-1 (GND - Body ground Always Below 1 Ω




OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


U190278E02
3.74,0.865 3.813,1.042 true 1.563,0.875 1.51,1.042 true 0.521,0.875 0.479,1.042 true 0.125,0.073 0.313,0.229 0.188,0.156 10 false *a 2.01,1.417 2.24,1.594 0.229,0.177 10 false 3B 5.417,1.427 5.625,1.594 0.208,0.167 10 false 3A 5.427,0.198 5.656,0.365 0.229,0.167 10 false 3C 1.969,0.375 2.208,0.531 0.24,0.156 10 false MB 3.625,1.083 4.083,1.26 0.458,0.177 10 false BMPX 1.333,1.083 1.656,1.24 0.323,0.156 10 false GND 0.281,1.073 0.698,1.24 0.417,0.167 10 false BECU

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly
- -

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-27 - MB-1 (BECU) Always Below 1 Ω
3C-19 - MB-32 (BMPX) Always Below 1 Ω
3B-18 - MB-11 (GND Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY