Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) detects the condition of the front door courtesy light switch assembly using this circuit.

WIRING DIAGRAM

E249229E05
1.417,1.802 3.229,2.146 1.813,0.344 10 false Front Door Courtesy Light Switch Assembly RH*1/LH*2 1.427,3.25 3.24,3.594 1.813,0.344 10 false Front Door Courtesy Light Switch Assembly LH*1/RH*2 4.135,3.073 5.74,3.427 1.604,0.354 10 false Instrument Panel Junction Block Assembly 5.469,4.063 6.99,4.417 1.521,0.354 10 false Main Body ECU (Network Gateway ECU) 1.406,1.635 2.271,1.813 0.865,0.177 10 false G18*1,H21*2 1.427,3.094 2.25,3.26 0.823,0.167 10 false H21*1,G18*2 4.552,1.167 4.76,1.333 0.208,0.167 10 false 3A 4.552,1 4.729,1.167 0.177,0.167 10 false 28 4.552,2.604 4.74,2.76 0.188,0.156 10 false 3B 4.542,2.427 4.729,2.583 0.188,0.156 10 false 13 5.563,1.167 5.802,1.323 0.24,0.156 10 false MB 5.563,0.99 5.75,1.167 0.188,0.177 10 false 16 5.552,2.604 5.781,2.781 0.229,0.177 10 false MB 5.854,1.167 6.271,1.333 0.417,0.167 10 false FDCY 5.875,2.594 6.302,2.76 0.427,0.167 10 false FPCY 5.552,2.427 5.74,2.583 0.188,0.156 10 false 10 2.885,1.052 3,1.229 0.115,0.177 10 false 1 2.875,2.5 2.99,2.677 0.115,0.177 10 false 1 0.469,4.042 1.208,4.219 0.74,0.177 10 false *1: for RHD 0.479,4.365 1.219,4.542 0.74,0.177 10 false *2: for LHD

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

OK:

Normal conditions listed above are displayed.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal/ON or OFF ON: Driver side door closed
OFF: Driver side door open
-
P Door Courtesy SW Passenger side door courtesy light switch signal/ON or OFF ON: Passenger side door closed
OFF: Passenger side door open
-

Result:
Result Proceed to
OK A
Driver side door courtesy light switch or passenger side door courtesy light switch does not operate B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
a.

Remove the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL).


b.

Inspect the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).

OK:

Front door courtesy light switch assembly is normal.



Result:
Result Proceed to
OK (for Front LH) A
OK (for Front RH) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B (for RHD) or 3A (for LHD) instrument panel junction block assembly connector.


b.

Disconnect the H21 front door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
H21-1 - 3B-13 Always Below 1 Ω
H21-1 - Body ground Always 10 kΩ or higher


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
H21-1 - 3A-28 Always Below 1 Ω
H21-1 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below. (for RHD)

U147275E01
0.116,0.109 0.302,0.270 0.186,0.161 10 *a 2.061,0.504 2.288,0.660 0.228,0.156 10 MB 5.618,0.3 5.806,0.456 0.189,0.156 10 3B 1.864,1.374 2.261,1.514 0.397,0.140 10 FPCY 1.842,1.438 1.512,1.068 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-13 - MB-10 (FPCY) Always Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below. (for LHD)

U147274E01
0.15,0.139 0.336,0.300 0.186,0.161 10 *a 2.062,0.544 2.288,0.700 0.226,0.156 10 MB 5.652,0.344 5.840,0.500 0.189,0.156 10 3A 2.543,1.408 2.940,1.547 0.397,0.139 10 FDCY 2.132,1.072 2.524,1.47 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 - MB-16 (FDCY) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A (for RHD) or 3B (for LHD) instrument panel junction block assembly connector.


b.

Disconnect the G18 front door courtesy light switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G18-1 - 3A-28 Always Below 1 Ω
G18-1 - Body ground Always 10 kΩ or higher


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G18-1 - 3B-13 Always Below 1 Ω
G18-1 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below. (for RHD)

U147274E01
0.15,0.139 0.336,0.300 0.186,0.161 10 *a 2.062,0.544 2.288,0.700 0.226,0.156 10 MB 5.652,0.344 5.840,0.500 0.189,0.156 10 3A 2.543,1.408 2.940,1.547 0.397,0.139 10 FDCY 2.132,1.072 2.524,1.47 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 - MB-16 (FDCY) Always Below 1 Ω



d.

Measure the resistance according to the value(s) in the table below. (for LHD)

U147275E01
0.116,0.109 0.302,0.270 0.186,0.161 10 *a 2.061,0.504 2.288,0.660 0.228,0.156 10 MB 5.618,0.3 5.806,0.456 0.189,0.156 10 3B 1.864,1.374 2.261,1.514 0.397,0.140 10 FPCY 1.842,1.438 1.512,1.068 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-13 - MB-10 (FPCY) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY