Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (network gateway ECU).

WIRING DIAGRAM

E254480E02
1.365,1.052 2.135,1.24 0.771,0.188 10 false from Battery 0.656,1.49 2.156,1.844 1.5,0.354 10 false from Certification ECU*1 or Ignition Switch*2 0.104,3.115 1.979,3.302 1.875,0.188 10 false *1: w/ Entry and Start System 0.104,3.438 2.052,3.646 1.948,0.208 10 false *2: w/o Entry and Start System 4.479,1.198 5.135,1.365 0.656,0.167 10 false ECU ACC 3.667,1.771 4.052,1.938 0.385,0.167 10 false ACC1 3.094,1.042 3.281,1.208 0.188,0.167 10 false 3E 3.083,1.469 3.292,1.625 0.208,0.156 10 false 3B 3.083,1.896 3.302,2.063 0.219,0.167 10 false 3A 3.083,2.302 3.292,2.469 0.208,0.167 10 false 3A 3.146,0.875 3.271,1.031 0.125,0.156 10 false 1 3.083,0.646 3.271,0.813 0.188,0.167 10 false 3B 3.115,0.469 3.302,0.625 0.188,0.156 10 false 28 5.552,1.042 5.802,1.198 0.25,0.156 10 false MB 5.583,0.875 5.708,1.042 0.125,0.167 10 false 9 3.104,1.292 3.302,1.438 0.198,0.146 10 false 20 3.094,1.708 3.281,1.875 0.188,0.167 10 false 12 3.094,2.125 3.271,2.292 0.177,0.167 10 false 13 5.469,3.135 6.979,3.479 1.51,0.344 10 false Main Body ECU (Network Gateway ECU) 3.083,2.771 5.719,2.958 2.635,0.188 10 false Instrument Panel Junction Block Assembly 5.573,0.323 5.771,0.49 0.198,0.167 10 false D5 5.573,0.146 5.75,0.313 0.177,0.167 10 false 22 5.229,0.719 5.396,0.885 0.167,0.167 10 false *1 5.885,1.042 6.208,1.208 0.323,0.167 10 false ACC 5.885,0.323 6.208,0.49 0.323,0.167 10 false ACC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

OK:

Normal conditions listed above are displayed.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal/ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
-



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the 3A and 3E instrument panel junction block assembly connectors.


b.
U147279E03
0.125,0.052 0.313,0.208 0.188,0.156 10 false *a 1.656,0.365 1.844,0.521 0.188,0.156 10 false 3E 1.656,2.719 1.844,2.875 0.188,0.156 10 false 3A

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V
3A-20 - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-12 - Body ground Always Below 1 Ω
3A-13 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/o Entry and Start System) A
OK (w/ Entry and Start System) B
NG C


Text in Illustration
*a Front view of wire harness connector
(to instrument panel junction block assembly)


A

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY)

B

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U147273E01
0.107,0.118 0.293,0.279 0.186,0.161 10 *a 1.581,0.302 1.771,0.458 0.190,0.156 10 3E 5.347,0.302 5.536,0.458 0.189,0.156 10 3A 3.636,1.579 3.863,1.736 0.226,0.156 10 MB 2.332,2.449 2.649,2.588 0.317,0.139 10 ACC 2.964,2.16 2.649,2.511 false

Text in Illustration
*a Component without harness connected
(Instrument panel junction block assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - MB-9 (ACC) Always 10 kΩ or higher
3E-1 - MB-9 (ACC) Battery positive (+) → 3A-20
Battery negative (-) → 3A-12 or 3A-13
Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1 RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U190457E01
0.868,0.265 1.055,0.423 0.187,0.159 10 3E 3.109,0.265 3.296,0.423 0.187,0.159 10 3A 5.767,0.265 5.954,0.423 0.187,0.159 10 3B 3.69,1.627 3.920,1.786 0.230,0.159 10 MB 0.209,0.215 0.372,0.357 0.163,0.142 10 *a 2.374,2.423 2.693,2.567 0.319,0.144 10 ACC 2.965,2.157 2.694,2.487 false

Text in Illustration
*a Component without harness connected
(Instrument panel junction block assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - MB-9 (ACC) Always 10 kΩ or higher
3E-1 - 3B-28 Always 10 kΩ or higher
3E-1 - MB-9 (ACC) Battery positive (+) → 3A-20
Battery negative (-) → 3A-12 or 3A-13
Below 1 Ω
3E-1 - 3B-28 Battery positive (+) → 3A-20
Battery negative (-) → 3A-12 or 3A-13
Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-28 - D5-22 (ACC) Always Below 1 Ω
3B-28 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR