Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E212454E10
2.968,1.179 3.390,1.353 0.422,0.174 10 AGND 4.735,1.266 5.157,1.441 0.422,0.174 10 AGND 3.033,0.784 3.390,0.958 0.357,0.174 10 SWIL 4.735,0.871 5.092,1.046 0.357,0.174 10 SWIL 4.484,1.179 4.659,1.353 0.175,0.174 10 24 4.487,0.784 4.659,0.958 0.172,0.174 10 16 3.466,1.179 3.563,1.353 0.097,0.174 10 6 3.466,0.784 3.561,0.958 0.095,0.174 10 9 1.833,1.69 2.143,1.865 0.310,0.174 10 D25 1.833,1.849 2.949,2.024 1.116,0.174 10 Engine Switch 4.32,1.62 4.654,1.795 0.334,0.174 10 D41 4.32,1.779 6.136,2.111 1.816,0.332 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the following inspection, check that the engine switch illumination has not been turned off using the rheostat function.

·

The engine switch illumination can be turned off by using the rheostat knob to select the minimum illuminance level with the taillights on.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the illumination operates.

OK:

Engine switch illumination comes on.


Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Engine switch illumination ON/OFF -



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH
a.

Remove the engine switch (See page Engine / Hybrid System>FA20 STARTING>ENGINE SWITCH>REMOVAL).


b.

OK:

Engine switch illumination comes on.



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D25 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D41-16 (SWIL) - D25-9 (SWIL) Always Below 1 Ω
D41-24 (AGND) - D25-6 (AGND) Always Below 1 Ω
D41-16 (SWIL) - Body ground Always 10 kΩ or higher
D41-24 (AGND) - Body ground Always Below 1 Ω




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR