Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.06
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

The ODO/TRIP display of the combination meter changes each time the trip switch is pressed.

HINT:

For more information about switching between displays, refer to the owner's manual.


WIRING DIAGRAM

E249058E04
5.396,0.948 5.948,1.156 0.552,0.208 10 false DISP*1 5.406,1.792 5.792,1.948 0.385,0.156 10 false CS*2 3.667,1.688 4.094,1.885 0.427,0.198 10 false CS*2 5.417,2.646 5.802,2.802 0.385,0.156 10 false TRIP 3.708,2.531 4.094,2.688 0.385,0.156 10 false TRIP 4.948,3.302 6.917,3.646 1.969,0.344 10 false Combination Meter Assembly 2.458,3.365 3.438,3.708 0.979,0.344 10 false Trip Switch 2.583,1.083 3.573,1.427 0.99,0.344 10 false DISP Switch*1 2.469,1.917 3.885,2.26 1.417,0.344 10 false km/h / MPH switch*2 0.073,3.229 1.781,3.573 1.708,0.344 10 false *2 : w/ km/h / MPH switch 0.073,2.938 1.781,3.281 1.708,0.344 10 false *1 : except TFT Meter Type 2.563,2.802 3.708,3.146 1.146,0.344 10 false ODO/TRIP Switch 4.948,3.146 5.156,3.302 0.208,0.156 10 false D7 2.469,3.219 2.76,3.375 0.292,0.156 10 false D64 5.146,0.833 5.448,0.99 0.302,0.156 10 false 34 5.146,2.542 5.344,2.698 0.198,0.156 10 false 36 4.104,0.854 4.479,1.063 0.375,0.208 10 false 3 5.177,1.698 5.531,1.854 0.354,0.156 10 false 35 4.115,1.698 4.385,1.885 0.271,0.188 10 false 8 1.76,1.646 1.958,1.802 0.198,0.156 10 false 1 4.104,2.531 4.302,2.688 0.198,0.156 10 false 2 3.563,0.854 4.115,1.063 0.552,0.208 10 false DISP*1

PROCEDURE

1.READ VALUE USING GTS (MULTI DISPLAY SELECT SWITCH, ODO/TRIP CHANGE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ODO/TRIP Change SW ODO/TRIP switch / OFF or ON OFF: ODO/TRIP switch not pushed -
ON: ODO/TRIP switch pushed
Multi Display Select Switch Multi Display Select Switch / OFF or ON OFF: DISP switch not pushed -
ON: DISP switch pushed

OK:

The value displayed on the GTS changes in accordance with the actual ODO/TRIP change switch and multi display select switch operation.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH
a.
E249059E02
1.333,2.5 1.021,2.042 true 1.625,3.01 1.906,2.552 true 2.313,2.99 2.021,2.552 true 0.792,1.938 1.104,2.135 0.313,0.198 10 false CS 1.344,3.031 1.729,3.229 0.385,0.198 10 false DISP 2.292,3 2.677,3.198 0.385,0.198 10 false TRIP 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a

Remove the trip switch (See page Vehicle Interior>METER / GAUGE / DISPLAY>TRIP SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (TRIP) - 1 ODO/TRIP switch on
(pushed)
Below 1 Ω
2 (TRIP) - 1 ODO/TRIP switch off
(not pushed)
10 kΩ or higher
3 (DISP) - 1*1 DISP switch on
(pushed)
Below 1 Ω
3 (DISP) - 1*1 DISP switch off
(not pushed)
10 kΩ or higher
8 (CS) - 1*2 km/h/MPH switch on
(pushed)
Below 1 Ω
8 (CS) - 1*2 km/h/MPH switch off
(not pushed)
10 kΩ or higher



*1: except TFT Meter Type

*2 : w/ km/h / MPH Switch

Text in Illustration
*a Component without harness connected
(Trip Switch)


OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - TRIP SWITCH AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - TRIP SWITCH AND BODY GROUND)
a.

Disconnect the D7 combination meter assembly connector.


b.

Disconnect the D64 trip switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D7-34 (DISP) - D64-3 (DISP)*1 Always Below 1 Ω
D7-35 (CS) - D64-8 (CS)*2 Always Below 1 Ω
D7-36 (TRIP) - D64-2 (TRIP) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D7-34 (DISP) or D64-3 (DISP) - Body ground*1 Always 10 kΩ or higher
D7-35 (CS) or D64-8 (CS) - Body ground*2 Always 10 kΩ or higher
D7-36 (TRIP) or D64-2 (TRIP) - Body ground Always 10 kΩ or higher



*1: except TFT Meter Type

*2 : w/ km/h / MPH Switch


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR