Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2016.06
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly controls the speedometer in accordance with the vehicle speed signals from the skid control ECU (brake actuator assembly) through the CAN communication system.

WIRING DIAGRAM

E220689E11
4.708,2.094 4.917,2.25 0.208,0.156 10 false D7 4.698,2.26 6.219,2.917 1.521,0.656 10 false COMBINATION METER ASSEMBLY 1.125,2.104 1.333,2.26 0.208,0.156 10 false A5 1.104,2.271 3.083,2.927 1.979,0.656 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 2.802,1.333 4.427,1.656 1.625,0.323 10 false CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the tester, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200, 240 km/h -

OK:

The vehicle speed displayed on the tester is approximately the same as that of the speedometer reading.




OK

3.READ VALUE USING GTS (VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed /
Min.: 0 (0)
Max.: 255 (158)
Approximately same as actual vehicle speed (when vehicle is being driven) Unit km/h (mph)

OK:

The vehicle speed displayed on the tester is approximately the same as the actual vehicle speed.


NOTICE:

Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).




OK

4.CHECK VEHICLE STABILITY CONTROL SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Check if the vehicle stability control system outputs DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).


Result
Result Proceed to
DTCs are not output. A
DTCs are output. B


A

5.READ VALUE USING GTS (VEHICLE SPEED)

B

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed /
Min.: 0 (0)
Max.: 326.4 (202.8)
Approximately same as actual vehicle speed (when vehicle is being driven) Unit km/h (mph)

OK:

The vehicle speed displayed on the tester is approximately the same as the actual vehicle speed.


NOTICE:

Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).




OK

6.REPLACE COMBINATION METER ASSEMBLY

NG

6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).

OK:

The operation of the speedometer returns to normal.




OK

END

NG