Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1610  Front Airbag Sensor RH Malfunction  B16F2  Front Airbag Sensor RH Mismatch  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag ECU assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH.

DTC No. DTC Detection Condition Trouble Area
B1610
·

Front airbag sensor RH malfunction

·

Airbag ECU assembly malfunction


·

Front airbag sensor RH

·

Airbag ECU assembly


B16F2
·

Improper installation of front airbag sensor RH

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK FRONT AIRBAG SENSOR RH
a.
C238211E01
2.195,0.812 2.316,0.967 0.121,0.156 10 A 2.036,0.812 2.157,0.967 0.121,0.156 10 B 1.581,0.812 1.703,0.967 0.121,0.156 10 C 1.425,0.812 1.546,0.967 0.121,0.156 10 D 0.98,0.812 1.101,0.967 0.121,0.156 10 E 0.829,0.812 0.950,0.967 0.121,0.156 10 F 0.514,0.812 0.698,0.989 0.184,0.178 10 *1 2.585,1.092 2.752,1.238 0.167,0.146 10 *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the front airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1610, B1615, B16F2 and B16F3 are not output. A
DTC B1610, B16F2 are output. B
DTC B1615, B16F3 are output. C


HINT:

Codes other than DTCs B1610, B1615, B16F2 and B16F3 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly



A

B

C