Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1620  Side Airbag Sensor RH Circuit Malfunction  B16F4  Side Airbag Sensor RH Mismatch  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH, rear airbag sensor RH and No. 2 airbag sensor assembly.

The side No. 2 airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the side No. 2 airbag sensor assembly RH.

DTC No. DTC Detection Condition Trouble Area
B1620
·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Side No. 2 airbag sensor assembly RH

·

Airbag ECU assembly


B16F4
·

Improper installation of side No. 2 airbag sensor assembly RH

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

Refer to DTCs B1622, B1623, B1632, B1633, B1642, B1692 and B1693 (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>B1622).

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238218E01
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1620 or B16F4 is output. A
DTC B1625 or B16F5 is output. B
DTCs B1620, B1625, B16F4 and B16F5 are not output. C


HINT:

Codes other than DTCs B1620,B1625,B16F4 and B16F5 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Airbag ECU Assembly



A

B

C