Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805  Short in P Squib Circuit  B1806  Open in P Squib Circuit  B1807  Short in P Squib Circuit (to Ground)  B1808  Short in P Squib Circuit (to +B)  


DESCRIPTION

The front passenger side squib circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1805
·

The airbag ECU assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


B1806
·

The airbag ECU assembly receives an open circuit signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


B1807
·

The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


B1808
·

The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C263726E01
0.138,2.619 0.411,2.756 0.273,0.137 10 D30 4.831,3.025 5.105,3.162 0.273,0.137 10 D27 0.124,2.768 2.974,3.091 2.850,0.323 10 Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 4.817,3.174 6.213,3.321 1.396,0.147 10 Airbag ECU Assembly 2.414,1.074 2.510,1.214 0.097,0.140 10 2 4.718,1.174 4.910,1.313 0.192,0.139 10 P+ 4.718,2.015 4.910,2.154 0.192,0.139 10 P- 2.126,1.074 2.318,1.213 0.192,0.139 10 P+ 2.161,1.909 2.319,2.048 0.158,0.139 10 P- 4.397,1.074 4.622,1.214 0.226,0.140 10 3*2 4.397,1.909 4.622,2.049 0.226,0.140 10 4*2 4.397,0.92 4.622,1.060 0.226,0.140 10 4*1 4.397,1.755 4.622,1.895 0.226,0.140 10 3*1 2.414,1.909 2.639,2.049 0.226,0.140 10 1*2 2.414,1.755 2.639,1.895 0.226,0.140 10 3*1 0.168,3.473 1.380,3.615 1.211,0.142 10 *1: w/o Dual Airbag 1.611,3.473 2.753,3.615 1.142,0.142 10 *2: w/ Dual Airbag

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C263727E01
0.454,0.976 0.607,1.112 0.152,0.137 10 *1 1.28,1.384 1.432,1.520 0.152,0.137 10 *3 2.417,0.886 2.569,1.023 0.152,0.137 10 *2 1.978,0.578 2.088,0.714 0.110,0.136 10 A 1.592,0.578 1.702,0.714 0.110,0.136 10 B 1.012,0.578 1.131,0.714 0.118,0.136 10 C 0.626,0.578 0.745,0.714 0.118,0.136 10 D 1.362,1.36 1.362,0.718 false 0.538,0.955 0.538,0.718 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire



OK

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.

Connect the connector to the airbag ECU assembly.

U190385E02
2.167,2.073 2.021,2.073 false 5.365,2.479 5.052,2.479 false 0.885,0.635 0.885,0.427 false 4.344,0.635 4.344,0.427 false 0.135,0.104 0.313,0.25 0.177,0.146 10 false *A 0.781,1.375 0.927,1.521 0.146,0.146 10 false *a 0.823,0.646 0.969,0.792 0.146,0.146 10 false *1 2.604,0.563 2.75,0.708 0.146,0.146 10 false *2 3.49,0.104 3.698,0.344 0.208,0.24 10 false *B 2.26,0.302 2.396,0.469 0.135,0.167 10 false A 2.125,0.292 2.219,0.479 0.094,0.188 10 false B 1.354,0.292 1.49,0.479 0.135,0.188 10 false C 1.031,0.292 1.146,0.458 0.115,0.167 10 false D 0.854,1.74 1.125,1.896 0.271,0.156 10 false D30 2.219,2 2.615,2.271 0.396,0.271 10 false SST 4.198,1.375 4.344,1.521 0.146,0.146 10 false *a 4.271,0.646 4.417,0.792 0.146,0.146 10 false *1 6.063,0.563 6.208,0.708 0.146,0.146 10 false *2 5.698,0.292 5.833,0.479 0.135,0.188 10 false A 5.573,0.292 5.708,0.51 0.135,0.219 10 false B 4.802,0.292 4.948,0.5 0.146,0.208 10 false C 4.469,0.292 4.615,0.51 0.146,0.219 10 false D 4.302,1.74 4.573,1.896 0.271,0.156 10 false D30 5.396,2.396 5.708,2.594 0.313,0.198 10 false SST

Text in Illustration
*A w/o Dual Airbag *B w/ Dual Airbag
*1 Instrument Panel Passenger Airbag Assembly *2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
- -


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTCs B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
U147137E02
0.51,0.792 0.51,0.521 false 1.76,0.792 1.76,0.521 false 0.438,0.802 0.583,0.948 0.146,0.146 10 false *1 0.26,1.583 0.406,1.729 0.146,0.146 10 false *a 2.792,0.615 2.938,0.76 0.146,0.146 10 false *2 1.667,0.781 1.813,0.927 0.146,0.146 10 false *3 2.521,0.333 2.635,0.49 0.115,0.156 10 false A 2.198,0.333 2.313,0.5 0.115,0.167 10 false B 0.802,0.344 0.906,0.521 0.104,0.177 10 false D 1.104,0.344 1.219,0.51 0.115,0.167 10 false C 0.458,2.333 0.729,2.49 0.271,0.156 10 false D30

Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - Body ground Ignition switch ON Below 1 V
D30-3 (P-) - Body ground Ignition switch ON Below 1 V


Standard Voltage:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - Body ground Ignition switch ON Below 1 V
D30-1 (P-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - D30-3 (P-) Always Below 1 Ω


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - D30-1 (P-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - Body ground Always 1 MΩ or higher
D30-3 (P-) - Body ground Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - Body ground Always 1 MΩ or higher
D30-1 (P-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - D30-3 (P-) Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D30-2 (P+) - D30-1 (P-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)




OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C260971E01
0.496,1.207 0.646,1.346 0.150,0.138 10 *1 2.501,1.021 2.651,1.159 0.150,0.138 10 *2 2.093,0.736 2.202,0.874 0.110,0.138 10 A 1.935,0.736 2.045,0.874 0.110,0.138 10 B 0.994,0.736 1.112,0.874 0.118,0.138 10 C 0.839,0.736 0.956,0.874 0.118,0.138 10 D 0.574,1.191 0.574,0.884 false

Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTCs B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly



OK

NG