Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860  Short in Knee Airbag (D Side) Squib Circuit  B1861  Open in Knee Airbag (D Side) Squib Circuit  B1862  Short in Knee Airbag (D Side) Squib Circuit (to Ground)  B1863  Short in Knee Airbag (D Side) Squib Circuit (to +B)  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag ECU assembly and lower No. 1 instrument panel airbag assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1860
·

The airbag ECU assembly receives a line short circuit signal in the driver side knee airbag squib circuit during primary check.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag ECU assembly


B1861
·

The airbag ECU assembly receives an open circuit signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


B1862
·

The airbag ECU assembly receives a short circuit to ground signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


B1863
·

The airbag ECU assembly receives a short circuit to B+ signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C263726E05
0.432,2.614 0.729,2.751 0.297,0.137 10 D62 4.817,3.02 5.091,3.158 0.273,0.137 10 D27 0.418,2.764 3.597,3.086 3.179,0.323 10 Lower NO. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 4.803,3.17 6.202,3.316 1.399,0.147 10 Airbag ECU Assembly 2.414,1.069 2.509,1.209 0.096,0.140 10 2 2.414,1.905 2.514,2.045 0.100,0.140 10 1 4.718,1.17 5.061,1.309 0.343,0.139 10 DK+ 4.718,2.01 5.022,2.149 0.304,0.139 10 DK- 2.013,1.069 2.305,1.208 0.292,0.139 10 DK+ 2.046,1.905 2.305,2.044 0.259,0.139 10 DK- 4.528,1.069 4.623,1.209 0.096,0.140 10 9 4.447,1.905 4.623,2.045 0.176,0.140 10 10

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238350E05
0.521,1.021 0.521,1.635 false 1.385,0.885 1.385,0.458 1.385,0.458 1.615,0.458 false 0.646,0.885 0.771,1.042 0.125,0.156 10 false D 1.042,0.885 1.167,1.042 0.125,0.156 10 false C 1.615,0.885 1.74,1.042 0.125,0.156 10 false B 2.021,0.885 2.146,1.042 0.125,0.156 10 false A 2.469,1.188 2.646,1.365 0.177,0.177 10 false *2 0.448,1.656 0.604,1.813 0.156,0.156 10 false *1 1.635,0.375 1.792,0.531 0.156,0.156 10 false *3

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
a.
U190321E02
0.656,0.667 0.656,1.063 false 1.792,2.292 1.969,2.292 false 0.573,1.104 0.729,1.271 0.156,0.167 10 false *1 2.25,0.844 2.417,1.01 0.167,0.167 10 false *2 1.813,0.521 1.979,0.688 0.167,0.167 10 false A 1.656,0.51 1.823,0.677 0.167,0.167 10 false B 1.146,0.521 1.313,0.688 0.167,0.167 10 false C 0.781,0.521 0.948,0.688 0.167,0.167 10 false D 0.458,2.219 0.729,2.396 0.271,0.177 10 false D62 2.031,2.219 2.344,2.385 0.313,0.167 10 false SST 0.375,1.719 0.531,1.885 0.156,0.167 10 false *a

Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the lower No. 1 instrument panel airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTCs B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)



OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
U190322E02
1.375,0.531 1.375,0.219 1.375,0.219 1.229,0.219 false 0.583,0.667 0.583,1.01 false 1,2.927 1.344,2.375 true 1.521,2.375 1.896,2.927 true 0.49,1.031 0.646,1.198 0.156,0.167 10 false *1 2.385,0.823 2.552,0.99 0.167,0.167 10 false *2 1.938,0.521 2.104,0.688 0.167,0.167 10 false A 1.573,0.521 1.74,0.688 0.167,0.167 10 false B 1.073,0.521 1.24,0.688 0.167,0.167 10 false C 0.688,0.521 0.854,0.688 0.167,0.167 10 false D 0.333,1.833 0.49,2 0.156,0.167 10 false *a 0.646,2.417 0.917,2.594 0.271,0.177 10 false D62 1.052,0.135 1.208,0.302 0.156,0.167 10 false *3 0.74,2.917 1,3.115 0.26,0.198 10 false DK- 1.938,2.927 2.26,3.125 0.323,0.198 10 false DK+

Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D62-1 (DK-) - Body ground Ignition switch ON Below 1 V
D62-2 (DK+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D62-1 (DK-) - D62-2 (DK+) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D62-1 (DK-) - Body ground Always 1 MΩ or higher
D62-2 (DK+) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D62-1 (DK-) - D62-2 (DK+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)




OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238353E05
0.813,0.833 0.813,1.208 false 0.938,0.698 1.063,0.854 0.125,0.156 10 false D 1.073,0.688 1.198,0.844 0.125,0.156 10 false C 1.594,0.688 1.719,0.844 0.125,0.156 10 false B 1.74,0.677 1.865,0.833 0.125,0.156 10 false A 2.167,0.948 2.5,1.25 0.333,0.302 10 false *2 0.729,1.229 0.885,1.406 0.156,0.177 10 false *1

Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTCs B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly



OK

NG