Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651  Manual Cut OFF Switch Trouble  


DESCRIPTION

The airbag cut off switch circuit consists of the airbag ECU assembly and airbag cut off switch.

The front passenger airbag can be optionally deactivated via this circuit by turning the airbag cut off switch to the OFF position.

If the front passenger airbag is deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the passengers.

DTC B1651 is stored when a malfunction is detected in the airbag cut off switch circuit.

DTC No. DTC Detecting Condition Trouble Area
B1651
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag cut off switch circuit.

·

Airbag cut off switch malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Airbag cut off switch

·

Airbag ECU assembly



WIRING DIAGRAM

C263719E01
0.571,3.707 1.917,3.864 1.346,0.157 10 Airbag Cut Off Switch 5.313,3.734 5.593,3.891 0.280,0.157 10 D27 5.313,3.888 6.709,4.028 1.395,0.140 10 Airbag ECU Assembly 5.626,1.379 6.073,1.527 0.448,0.149 10 MSW+ 5.357,1.269 5.536,1.427 0.179,0.158 10 14 5.626,2.871 6.044,3.020 0.419,0.149 10 MSW- 2.328,1.269 2.765,1.418 0.437,0.149 10 MSW+ 2.361,2.761 2.766,2.910 0.405,0.149 10 MSW- 5.357,2.761 5.536,2.919 0.179,0.158 10 12 2.884,1.269 2.982,1.427 0.098,0.158 10 2 2.884,2.761 2.982,2.919 0.098,0.158 10 1 0.57,3.538 0.925,3.727 0.355,0.188 10 D37

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch.

OK:

The connectors are properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and airbag cut off switch.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

2.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Using a service wire, connect terminals 12 (MSW-) and 14 (MSW+) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.
U190382E02
1.927,0.781 1.594,1.24 true 2.104,0.781 2.438,1.24 true 1.698,2.646 1.552,2.646 1.552,2.646 1.552,2.292 false 1.458,4.219 1.625,3.917 true 1.875,3.917 2.01,4.219 true 1.198,0.667 1.469,0.823 0.271,0.156 10 false D27 0.875,3.698 1.146,3.854 0.271,0.156 10 false D37 2.49,1.177 2.99,1.385 0.5,0.208 10 false MSW+ 1.135,1.177 1.604,1.417 0.469,0.24 10 false MSW- 2.052,4.146 2.49,4.354 0.438,0.208 10 false MSW+ 1.021,4.146 1.458,4.365 0.438,0.219 10 false MSW- 0.885,0.208 1.042,0.354 0.156,0.146 10 false *a 0.26,3.188 0.417,3.333 0.156,0.146 10 false *b 0.635,2.135 0.781,2.281 0.146,0.146 10 false *1 2.469,2.427 2.615,2.573 0.146,0.146 10 false *2 2.063,2.146 2.177,2.292 0.115,0.146 10 false A 1.719,2.146 1.833,2.292 0.115,0.146 10 false B 1.271,2.146 1.385,2.292 0.115,0.146 10 false C 0.938,2.146 1.052,2.292 0.115,0.146 10 false D 1.719,2.563 1.865,2.708 0.146,0.146 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-1 (MSW-) - D37-2 (MSW+) Always Below 1 Ω


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

3.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-2 (MSW+) - D37-1 (MSW-) Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D37-1 (MSW-) - Body ground Ignition switch ON Below 1 V
D37-2 (MSW+) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U190383E02
1.656,1.198 1.51,1.198 1.51,1.198 1.51,0.781 false 1.781,2.802 1.927,2.479 true 2.208,2.479 2.292,2.802 true 0.51,1.719 0.667,1.865 0.156,0.146 10 false *a 0.615,0.625 0.76,0.771 0.146,0.146 10 false *1 2.448,0.906 2.594,1.052 0.146,0.146 10 false *2 1.677,1.125 1.823,1.271 0.146,0.146 10 false *3 1.208,2.24 1.479,2.396 0.271,0.156 10 false D37 2.042,0.625 2.167,0.792 0.125,0.167 10 false A 1.698,0.625 1.833,0.833 0.135,0.208 10 false B 1.26,0.625 1.396,0.823 0.135,0.198 10 false C 0.917,0.625 1.052,0.813 0.135,0.188 10 false D 1.323,2.729 1.74,2.938 0.417,0.208 10 false MSW- 2.344,2.729 2.802,2.979 0.458,0.25 10 false MSW+

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D37-1 (MSW-) - Body ground Always 1 MΩ or higher
D37-2 (MSW+) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch)



OK

6.CHECK AIRBAG CUT OFF SWITCH

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK AIRBAG CUT OFF SWITCH

OK

7.CHECK DTC

NG

7.CHECK DTC
a.
C238328E02
0.667,0.802 0.854,0.958 0.188,0.156 10 false *1 1.875,0.802 2.063,0.958 0.188,0.156 10 false A 1.719,0.802 1.906,0.958 0.188,0.156 10 false B 1.25,0.802 1.438,0.958 0.188,0.156 10 false C 1.083,0.802 1.271,0.958 0.188,0.156 10 false D 2.333,1.115 2.521,1.271 0.188,0.156 10 false *2

Connect the connectors to the airbag ECU assembly and airbag cut off switch.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1651 is not output.


Text in Illustration
*1 Airbag Cut Off Switch
*2 Airbag ECU Assembly

HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.




OK

NG