Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660  P Seat Airbag Active Mode Indicator  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag ECU assembly and clock assembly (passenger airbag ON/OFF indicator).

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag and front seat belt pretensioner RH.

DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. DTC Detection Condition Trouble Area
B1660
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit.

·

Clock assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Clock assembly (Passenger airbag ON/OFF indicator)

·

Airbag ECU assembly



WIRING DIAGRAM

C239224E28
1.292,1.094 2,1.396 0.708,0.302 10 false PAON 1.344,2.094 1.99,2.438 0.646,0.344 10 false P-AB 1.323,3.094 1.854,3.458 0.531,0.365 10 false LAPB 1.771,2.99 2.052,3.385 0.281,0.396 10 false 10 1.781,1.979 2.25,2.344 0.469,0.365 10 false 5 1.781,0.979 2.135,1.375 0.354,0.396 10 false 3 5.49,1.094 6.031,1.5 0.542,0.406 10 false PAON 5.49,2.094 6.031,2.438 0.542,0.344 10 false PAOFF 5.49,3.104 5.854,3.365 0.365,0.26 10 false GND 5.229,2.99 5.635,3.375 0.406,0.385 10 false 25 5.229,4 5.698,4.396 0.469,0.396 10 false 26 5.229,1.979 5.771,2.458 0.542,0.479 10 false 17 5.229,0.979 5.594,1.385 0.365,0.406 10 false 23 2.667,4.073 3.625,4.427 0.958,0.354 10 false from IG2 Relay 0.552,4.76 1,5.083 0.448,0.323 10 false D18 0.552,4.948 2.333,5.448 1.781,0.5 10 false Clock Assembly (Passenger Airbag ON/OFF Indicator) 5.396,4.75 5.844,5.094 0.448,0.344 10 false D27 5.396,4.927 7,5.302 1.604,0.375 10 false Airbag ECU Assembly 2.167,3.25 3.156,3.521 0.99,0.271 10 false GAUGE 5.5,4.104 5.865,4.365 0.365,0.26 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

Result:
ON/OFF Indicator Illumination Proceed to
Always ON A
OFF B


HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).




A

2.CHECK CONNECTORS

B

9.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and clock assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and clock assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the clock assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE (OPEN)
4.CHECK DTC
a.
C238328E02
0.667,0.802 0.854,0.958 0.188,0.156 10 false *1 1.875,0.802 2.063,0.958 0.188,0.156 10 false A 1.719,0.802 1.906,0.958 0.188,0.156 10 false B 1.25,0.802 1.438,0.958 0.188,0.156 10 false C 1.083,0.802 1.271,0.958 0.188,0.156 10 false D 2.333,1.115 2.521,1.271 0.188,0.156 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the airbag ECU assembly.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U147185E04
1.865,0.583 2.167,1.156 true 1.49,0.771 1.198,1.167 true 1.708,1.01 1.708,1.208 false 1.531,2.156 1.531,2.385 false 0.802,4.344 1.198,3.875 true 1.427,3.875 1.885,4.344 true 0.635,0.177 0.813,0.354 0.177,0.177 10 false *a 1.448,2.396 1.604,2.573 0.156,0.177 10 false *3 0.344,3.271 0.552,3.469 0.208,0.198 10 false *b 0.448,2.01 0.646,2.156 0.198,0.146 10 false *1 2.573,2.271 2.75,2.469 0.177,0.198 10 false *2 2.208,1.083 2.688,1.25 0.479,0.167 10 false PAOFF 0.427,3.792 0.698,3.969 0.271,0.177 10 false D18 0.781,0.5 1.052,0.677 0.271,0.177 10 false D27 0.677,1.083 1.104,1.26 0.427,0.177 10 false PAON 1.802,2.021 1.948,2.188 0.146,0.167 10 false B 0.865,2.021 1.01,2.188 0.146,0.167 10 false D 1.167,2.021 1.313,2.188 0.146,0.167 10 false C 2.094,2.021 2.24,2.188 0.146,0.167 10 false A 1.625,1.25 1.781,1.417 0.156,0.167 10 false *4 1.927,4.281 2.323,4.542 0.396,0.26 10 false P-AB 0.313,4.281 0.76,4.479 0.448,0.198 10 false PAON

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the clock assembly.


d.

Using a service wire, connect terminals 23 (PAON) and 17 (PAOFF) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - D18-5 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector B.

Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Clock Assembly)



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT)
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - D18-5 (P-AB) Always 1 MΩ or higher


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D18-3 (PAON) - Body ground Ignition switch ON Below 1 V
D18-5 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - Body ground Always 1 MΩ or higher
D18-5 (P-AB) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

REPLACE CLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and clock assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and clock assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

10.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U147185E04
1.865,0.583 2.167,1.156 true 1.49,0.771 1.198,1.167 true 1.708,1.01 1.708,1.208 false 1.531,2.156 1.531,2.385 false 0.802,4.344 1.198,3.875 true 1.427,3.875 1.885,4.344 true 0.635,0.177 0.813,0.354 0.177,0.177 10 false *a 1.448,2.396 1.604,2.573 0.156,0.177 10 false *3 0.344,3.271 0.552,3.469 0.208,0.198 10 false *b 0.448,2.01 0.646,2.156 0.198,0.146 10 false *1 2.573,2.271 2.75,2.469 0.177,0.198 10 false *2 2.208,1.083 2.688,1.25 0.479,0.167 10 false PAOFF 0.427,3.792 0.698,3.969 0.271,0.177 10 false D18 0.781,0.5 1.052,0.677 0.271,0.177 10 false D27 0.677,1.083 1.104,1.26 0.427,0.177 10 false PAON 1.802,2.021 1.948,2.188 0.146,0.167 10 false B 0.865,2.021 1.01,2.188 0.146,0.167 10 false D 1.167,2.021 1.313,2.188 0.146,0.167 10 false C 2.094,2.021 2.24,2.188 0.146,0.167 10 false A 1.625,1.25 1.781,1.417 0.156,0.167 10 false *4 1.927,4.281 2.323,4.542 0.396,0.26 10 false P-AB 0.313,4.281 0.76,4.479 0.448,0.198 10 false PAON

Using a service wire, connect terminals 23 (PAON) and 17 (PAOFF) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - D18-5 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Clock Assembly)



OK

11.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - D18-5 (P-AB) Always 1 MΩ or higher


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D18-3 (PAON) - Body ground Ignition switch ON Below 1 V
D18-5 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

13.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U147186E03
1.531,0.74 1.531,0.958 false 0.927,2.927 1.198,2.469 true 1.438,2.469 1.635,2.927 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.313,1.854 0.521,2.052 0.208,0.198 10 false *a 0.448,0.594 0.646,0.74 0.198,0.146 10 false *1 2.573,0.844 2.75,1.042 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.51,2.875 0.948,3.135 0.438,0.26 10 false PAON 1.708,2.865 2.063,3.073 0.354,0.208 10 false P-AB

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (PAON) - Body ground Always 1 MΩ or higher
D18-5 (P-AB) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

14.CHECK CLOCK ASSEMBLY (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK CLOCK ASSEMBLY (SOURCE VOLTAGE)
a.
U147187E03
1.531,0.74 1.531,0.958 false 0.938,2.927 1.208,2.604 true 1.448,0.979 1.604,1.156 0.156,0.177 10 false *3 0.292,1.854 0.5,2.052 0.208,0.198 10 false *a 0.469,0.594 0.667,0.74 0.198,0.146 10 false *1 2.552,0.896 2.729,1.094 0.177,0.198 10 false *2 0.427,2.375 0.698,2.552 0.271,0.177 10 false D18 1.802,0.594 1.948,0.76 0.146,0.167 10 false B 0.875,0.594 1.021,0.76 0.146,0.167 10 false D 1.167,0.594 1.313,0.76 0.146,0.167 10 false C 2.094,0.594 2.24,0.76 0.146,0.167 10 false A 0.542,2.865 0.938,3.094 0.396,0.229 10 false LAPB

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D18-10 (LAPB) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Clock Assembly)



OK

15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR BATTERY

15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the clock assembly.


U147016E02
2.073,2.417 2.365,2.875 true 1.729,2.604 1.552,2.875 true 1.49,0.635 1.49,0.177 1.49,0.177 1.698,0.177 false 1.75,0.104 1.906,0.25 0.156,0.146 10 false *3 0.833,1.865 1.042,2.063 0.208,0.198 10 false *a 0.573,0.635 0.771,0.865 0.198,0.229 10 false *1 2.521,0.958 2.698,1.156 0.177,0.198 10 false *2 1.313,2.906 1.729,3.063 0.417,0.156 10 false PAON 0.969,2.292 1.24,2.469 0.271,0.177 10 false D27 2.156,2.906 2.688,3.073 0.531,0.167 10 false PAOFF 1.75,0.635 1.896,0.802 0.146,0.167 10 false B 0.969,0.635 1.115,0.802 0.146,0.167 10 false D 1.125,0.635 1.271,0.802 0.146,0.167 10 false C 2.042,0.635 2.188,0.802 0.146,0.167 10 false A

b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
D27-23 (PAON) - Body ground Ignition switch ON "ON" comes on
D27-17 (PAOFF) - Body ground Ignition switch ON "OFF" comes on



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)



OK

16.CHECK DTC

NG

REPLACE CLOCK ASSEMBLY

16.CHECK DTC
a.
C238328E02
0.667,0.802 0.854,0.958 0.188,0.156 10 false *1 1.875,0.802 2.063,0.958 0.188,0.156 10 false A 1.719,0.802 1.906,0.958 0.188,0.156 10 false B 1.25,0.802 1.438,0.958 0.188,0.156 10 false C 1.083,0.802 1.271,0.958 0.188,0.156 10 false D 2.333,1.115 2.521,1.271 0.188,0.156 10 false *2

Connect the connector to the airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Clock Assembly
*2 Airbag ECU Assembly



OK

NG