Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820  Short in Side Squib (RH) Circuit  B1821  Open in Side Squib (RH) Circuit  B1822  Short in Side Squib (RH) Circuit (to Ground)  B1823  Short in Side Squib (RH) Circuit (to +B)  


DESCRIPTION

The front side squib RH circuit consists of the airbag ECU assembly and front seat airbag assembly RH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1820
·

The airbag ECU assembly receives a line short circuit signal in the front side squib RH circuit during primary check.

·

Front side squib RH malfunction

·

Airbag ECU assembly malfunction


·

No. 2 floor wire

·

Front seat assembly RH (Front seat wire RH)

·

Front seat airbag assembly RH (Front side squib RH)

·

Airbag ECU assembly


B1821
·

The airbag ECU assembly receives an open circuit signal in the front side squib RH circuit.

·

Front side squib RH malfunction

·

Airbag ECU assembly malfunction


B1822
·

The airbag ECU assembly receives a short circuit to ground signal in the front side squib RH circuit.

·

Front side squib RH malfunction

·

Airbag ECU assembly malfunction


B1823
·

The airbag ECU assembly receives a short circuit to B+ signal in the front side squib RH circuit.

·

Front side squib RH malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C370985E01
0.698,2.531 0.906,2.719 0.208,0.188 10 false c1 4.667,3.063 4.979,3.26 0.313,0.198 10 false G1 0.688,2.708 2.708,3.115 2.021,0.406 10 false Front Seat Airbag Assembly RH (Front Side Squib RH) 1.958,1.063 2.438,1.281 0.479,0.219 10 false SFR+ 1.979,1.896 2.458,2.115 0.479,0.219 10 false SFR- 2.427,1.063 2.74,1.26 0.313,0.198 10 false 2 3.458,0.958 3.771,1.156 0.313,0.198 10 false 2 2.417,1.885 2.729,2.083 0.313,0.198 10 false 1 3.448,1.781 3.76,1.979 0.313,0.198 10 false 1 3.375,1.156 3.688,1.354 0.313,0.198 10 false Gc1 3.375,2 3.688,2.198 0.313,0.198 10 false Gc1 4.51,1.052 4.823,1.25 0.313,0.198 10 false 7 4.5,1.875 4.813,2.073 0.313,0.198 10 false 6 4.677,3.24 6.354,3.458 1.677,0.219 10 false Airbag ECU Assembly 4.708,1.156 5.188,1.375 0.479,0.219 10 false SFR+ 4.719,1.99 5.198,2.208 0.479,0.219 10 false SFR-

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C263729E01
0.167,1.48 0.318,1.617 0.151,0.137 10 *1 0.571,0.492 0.722,0.629 0.151,0.137 10 *3 1.748,1.549 1.899,1.686 0.151,0.137 10 *4 2.746,0.712 2.897,0.849 0.151,0.137 10 *2 0.248,1.458 0.248,1.161 false 0.751,0.564 0.995,0.564 0.995,0.564 0.995,1.029 false 1.833,1.524 1.833,1.161 false 2.358,1.021 2.468,1.157 0.110,0.137 10 A 2.094,1.021 2.205,1.157 0.110,0.137 10 B 1.521,1.021 1.639,1.157 0.118,0.137 10 C 1.258,1.021 1.376,1.157 0.118,0.137 10 D 0.635,1.021 0.745,1.157 0.110,0.137 10 E 0.379,1.021 0.481,1.157 0.102,0.137 10 F

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly RH and airbag ECU assembly. Also check that the connectors that link the No. 2 floor wire and front seat wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly RH and airbag ECU assembly. Also disconnect the No. 2 floor wire from the front seat wire RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the front seat wire RH connector (on the front seat airbag assembly RH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the No. 2 floor wire and the front seat wire RH with the activation prevention mechanism is not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (FRONT SIDE SQUIB RH)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (FRONT SIDE SQUIB RH)
a.
U147190E02
2.177,2.396 2.063,2.396 false 0.521,1.167 0.521,0.979 false 0.302,1.771 0.448,1.948 0.146,0.177 10 false *a 0.448,1.198 0.594,1.333 0.146,0.135 10 false *1 2.573,0.5 2.719,0.698 0.146,0.198 10 false *2 2.208,2.323 2.5,2.469 0.292,0.146 10 false SST 2.177,0.823 2.302,0.99 0.125,0.167 10 false A 2.01,0.833 2.125,0.979 0.115,0.146 10 false B 1.563,0.833 1.677,1.01 0.115,0.177 10 false C 1.406,0.844 1.521,0.99 0.115,0.146 10 false D 0.938,0.844 1.052,0.979 0.115,0.135 10 false E 0.646,0.844 0.75,0.979 0.104,0.135 10 false F 0.688,2.344 0.854,2.5 0.167,0.156 10 false c1

Connect the No. 2 floor wire to the front seat wire RH and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the front seat airbag assembly RH (front side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTCs B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)



OK

NG

3.CHECK FRONT SIDE SQUIB RH CIRCUIT
3.CHECK FRONT SIDE SQUIB RH CIRCUIT
a.
U147040E03
0.375,1.229 0.375,0.99 false 1.177,2.99 1.448,2.667 true 1.76,2.667 2.063,2.99 true 0.292,1.26 0.469,1.448 0.177,0.188 10 false *1 0.292,1.781 0.438,1.917 0.146,0.135 10 false *a 2.583,0.542 2.802,0.844 0.219,0.302 10 false *2 2.177,0.844 2.302,1.083 0.125,0.24 10 false A 1.854,0.844 2,1.063 0.146,0.219 10 false B 1.406,0.844 1.531,1.042 0.125,0.198 10 false C 1.25,0.844 1.365,1.042 0.115,0.198 10 false D 0.802,0.844 0.938,1.042 0.135,0.198 10 false E 0.5,0.844 0.635,1.063 0.135,0.219 10 false F 0.75,2.448 0.917,2.604 0.167,0.156 10 false c1 0.813,2.927 1.198,3.167 0.385,0.24 10 false SFR- 2.104,2.927 2.531,3.156 0.427,0.229 10 false SFR+

Disconnect the No. 2 floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - Body ground Ignition switch ON Below 1 V
c1-2 (SFR+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - c1-2 (SFR+) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - Body ground Always 1 MΩ or higher
c1-2 (SFR+) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - c1-2 (SFR+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)




OK

4.CHECK DTC

NG

5.CHECK NO. 2 FLOOR WIRE
4.CHECK DTC
a.
C245654E01
0.728,0.774 0.884,0.926 0.156,0.152 10 *1 2.533,0.996 2.707,1.152 0.174,0.156 10 *2 2.069,1.306 2.186,1.459 0.117,0.153 10 A 1.913,1.306 2.029,1.459 0.117,0.153 10 B 1.39,1.306 1.517,1.459 0.127,0.153 10 C 1.233,1.306 1.360,1.459 0.127,0.153 10 D 0.719,1.306 0.846,1.459 0.127,0.153 10 E 0.558,1.306 0.685,1.459 0.127,0.153 10 F 0.452,1.32 0.452,0.859 0.452,0.859 0.709,0.859 false

Connect the connectors to the front seat airbag assembly RH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTCs B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly



OK

NG

5.CHECK NO. 2 FLOOR WIRE
a.
U147041E02
0.271,0.823 0.271,0.365 0.271,0.365 0.531,0.365 false 1.75,0.823 1.75,0.365 1.75,0.365 1.906,0.365 false 1,0.99 1,1.333 false 0.563,0.302 0.719,0.458 0.156,0.156 10 false *1 2.656,0.469 2.833,0.625 0.177,0.156 10 false *2 2.26,0.813 2.375,0.969 0.115,0.156 10 false A 1.948,0.813 2.063,0.969 0.115,0.156 10 false B 1.49,0.813 1.615,0.969 0.125,0.156 10 false C 1.188,0.823 1.313,0.979 0.125,0.156 10 false D 0.74,0.823 0.865,0.979 0.125,0.156 10 false E 0.427,0.833 0.552,0.99 0.125,0.156 10 false F 0.302,1.729 0.469,1.896 0.167,0.167 10 false *a 0.76,2.406 1.031,2.563 0.271,0.156 10 false Gc1 1.958,0.292 2.115,0.448 0.156,0.156 10 false *4 0.927,1.323 1.073,1.479 0.146,0.156 10 false *3

Disconnect the front seat wire RH from the No. 2 floor wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Gc1-1 - Body ground Ignition switch ON Below 1 V
Gc1-2 - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gc1-1 - Gc1-2 Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gc1-1 - Body ground Always 1 MΩ or higher
Gc1-2 - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Gc1-1 - Gc1-2 Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire RH)


OK

6.CHECK FRONT SEAT WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK FRONT SEAT WIRE RH
a.
U147042E02
0.323,0.833 0.323,0.375 0.323,0.375 0.583,0.375 false 1.781,0.833 1.781,0.375 1.781,0.375 1.938,0.375 false 1.021,0.979 1.021,1.344 1.021,1.344 1.198,1.344 false 1.135,2.979 1.448,2.667 true 1.75,2.667 2.063,2.979 true 0.594,0.292 0.75,0.448 0.156,0.156 10 false *1 2.656,0.531 2.833,0.688 0.177,0.156 10 false *2 2.25,0.823 2.365,0.979 0.115,0.156 10 false A 1.938,0.823 2.052,0.979 0.115,0.156 10 false B 1.5,0.823 1.625,0.979 0.125,0.156 10 false C 1.188,0.823 1.313,0.979 0.125,0.156 10 false D 0.74,0.823 0.865,0.979 0.125,0.156 10 false E 0.438,0.823 0.563,0.979 0.125,0.156 10 false F 0.302,1.813 0.469,1.979 0.167,0.167 10 false *a 0.76,2.177 0.927,2.333 0.167,0.156 10 false c1 1.958,0.292 2.115,0.448 0.156,0.156 10 false *4 1.219,1.26 1.365,1.417 0.146,0.156 10 false *3 0.792,2.927 1.146,3.135 0.354,0.208 10 false SFR- 2.115,2.927 2.5,3.156 0.385,0.229 10 false SFR+

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - Body ground Ignition switch ON Below 1 V
c1-2 (SFR+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - c1-2 (SFR+) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - Body ground Always 1 MΩ or higher
c1-2 (SFR+) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (SFR-) - c1-2 (SFR+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Front Seat Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)


OK

NG

REPLACE FRONT SEAT ASSEMBLY RH