Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825  Short in Side Squib (LH) Circuit  B1826  Open in Side Squib (LH) Circuit  B1827  Short in Side Squib (LH) Circuit (to Ground)  B1828  Short in Side Squib (LH) Circuit (to +B)  


DESCRIPTION

The front side squib LH circuit consists of the airbag ECU assembly and front seat airbag assembly LH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1825
·

The airbag ECU assembly receives a line short circuit signal in the front side squib LH circuit during primary check.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front seat assembly LH (Front seat wire LH)

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag ECU assembly


B1826
·

The airbag ECU assembly receives an open circuit signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


B1827
·

The airbag ECU assembly receives a short circuit to ground signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction


B1828
·

The airbag ECU assembly receives a short circuit to B+ signal in the front side squib LH circuit.

·

Front side squib LH malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C370985E02
0.698,2.531 0.906,2.719 0.208,0.188 10 false b1 4.677,3.063 4.99,3.26 0.313,0.198 10 false H17 0.677,2.719 2.698,3.125 2.021,0.406 10 false Front Seat Airbag Assembly LH (Front Side Squib LH) 1.958,1.073 2.438,1.292 0.479,0.219 10 false SFL+ 1.979,1.896 2.458,2.115 0.479,0.219 10 false SFL- 2.427,1.063 2.74,1.26 0.313,0.198 10 false 2 3.458,0.958 3.771,1.156 0.313,0.198 10 false 2 2.417,1.885 2.729,2.083 0.313,0.198 10 false 1 3.448,1.781 3.76,1.979 0.313,0.198 10 false 1 3.375,1.156 3.688,1.354 0.313,0.198 10 false Hb1 3.375,2 3.688,2.198 0.313,0.198 10 false Hb1 4.51,1.052 4.823,1.25 0.313,0.198 10 false 9 4.448,1.875 4.76,2.073 0.313,0.198 10 false 10 4.667,3.24 6.344,3.458 1.677,0.219 10 false Airbag ECU Assembly 4.74,1.156 5.219,1.375 0.479,0.219 10 false SFL+ 4.729,1.99 5.208,2.208 0.479,0.219 10 false SFL-

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C263811E01
0.186,1.528 0.338,1.667 0.152,0.139 10 *1 0.504,0.497 0.656,0.636 0.152,0.139 10 *3 1.746,1.576 1.897,1.714 0.152,0.139 10 *4 2.745,1 2.897,1.139 0.152,0.139 10 *2 1.828,1.553 1.828,1.142 false 0.695,0.57 0.94,0.57 0.94,0.57 0.94,1.009 false 0.266,1.501 0.266,1.142 false 2.358,1.001 2.468,1.138 0.110,0.137 10 A 2.094,1.001 2.204,1.138 0.110,0.137 10 B 1.504,1.001 1.622,1.138 0.118,0.137 10 C 1.24,1.001 1.358,1.138 0.119,0.137 10 D 0.636,1.001 0.746,1.138 0.110,0.137 10 E 0.378,1.001 0.480,1.138 0.102,0.137 10 F

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly LH and airbag ECU assembly. Also check that the connectors that link the floor wire and front seat wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly LH and airbag ECU assembly. Also disconnect the floor wire from the front seat wire LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the front seat wire LH connector (on the front seat airbag assembly LH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the floor wire and the front seat wire LH with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Front Seat Wire LH
*4 Floor Wire



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)
a.
U147192E02
2.208,2.292 2.063,2.292 false 0.302,1.75 0.448,1.927 0.146,0.177 10 false *a 2.219,2.208 2.51,2.354 0.292,0.146 10 false SST 0.438,0.885 0.583,1.021 0.146,0.135 10 false *1 2.573,0.531 2.719,0.708 0.146,0.177 10 false *2 2.167,0.531 2.292,0.698 0.125,0.167 10 false A 2.01,0.542 2.125,0.698 0.115,0.156 10 false B 1.563,0.531 1.667,0.688 0.104,0.156 10 false C 1.406,0.531 1.521,0.688 0.115,0.156 10 false D 0.958,0.542 1.073,0.677 0.115,0.135 10 false E 0.656,0.542 0.76,0.677 0.104,0.135 10 false F 0.677,2.24 0.854,2.396 0.177,0.156 10 false b1

Connect the floor wire to the front seat wire LH and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the front seat airbag assembly LH (front side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U147037E02
0.375,0.781 0.375,1.042 false 1.188,2.927 1.448,2.667 true 1.75,2.667 2.021,2.927 true 0.281,1.792 0.448,1.958 0.167,0.167 10 false *a 0.302,1.052 0.458,1.208 0.156,0.156 10 false *1 2.594,0.635 2.771,0.792 0.177,0.156 10 false *2 2.167,0.625 2.281,0.781 0.115,0.156 10 false A 1.865,0.625 1.979,0.781 0.115,0.156 10 false B 1.417,0.625 1.542,0.781 0.125,0.156 10 false C 1.26,0.625 1.385,0.781 0.125,0.156 10 false D 0.813,0.625 0.938,0.781 0.125,0.156 10 false E 0.5,0.625 0.625,0.781 0.125,0.156 10 false F 0.76,2.396 0.938,2.552 0.177,0.156 10 false b1 0.833,2.865 1.188,3.094 0.354,0.229 10 false SFL- 2.063,2.865 2.417,3.094 0.354,0.229 10 false SFL+

Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - Body ground Ignition switch ON Below 1 V
b1-2 (SFL+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - b1-2 (SFL+) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - Body ground Always 1 MΩ or higher
b1-2 (SFL+) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - b1-2 (SFL+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)




OK

4.CHECK DTC

NG

5.CHECK FLOOR WIRE
4.CHECK DTC
a.
C238340E02
0.448,1.115 0.448,1.406 false 0.563,0.938 0.667,1.094 0.104,0.156 10 false F 0.708,0.938 0.833,1.094 0.125,0.156 10 false E 1.229,0.938 1.354,1.094 0.125,0.156 10 false D 1.385,0.938 1.51,1.094 0.125,0.156 10 false C 1.917,0.938 2.042,1.094 0.125,0.156 10 false B 2.073,0.938 2.198,1.094 0.125,0.156 10 false A 0.365,1.406 0.521,1.583 0.156,0.177 10 false *1 2.5,0.938 2.677,1.083 0.177,0.146 10 false *2

Connect the connectors to the front seat airbag assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly



OK

NG

5.CHECK FLOOR WIRE
a.
U147038E02
0.323,0.771 0.323,1.031 false 1,0.781 1,1.042 false 1.75,0.615 1.75,0.208 1.75,0.208 1.563,0.208 false 0.313,1.781 0.479,1.948 0.167,0.167 10 false *a 0.26,1.063 0.417,1.219 0.156,0.156 10 false *1 2.677,0.604 2.854,0.76 0.177,0.156 10 false *2 2.25,0.604 2.365,0.76 0.115,0.156 10 false A 1.948,0.615 2.063,0.771 0.115,0.156 10 false B 1.49,0.604 1.615,0.76 0.125,0.156 10 false C 1.177,0.615 1.302,0.771 0.125,0.156 10 false D 0.74,0.604 0.865,0.76 0.125,0.156 10 false E 0.427,0.615 0.552,0.771 0.125,0.156 10 false F 0.927,1.073 1.083,1.229 0.156,0.156 10 false *3 0.729,2.448 1,2.604 0.271,0.156 10 false Hb1 1.385,0.146 1.542,0.302 0.156,0.156 10 false *4

Disconnect the front seat wire LH from the floor wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Hb1-1 - Body ground Ignition switch ON Below 1 V
Hb1-2 - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hb1-1 - Hb1-2 Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hb1-1 - Body ground Always 1 MΩ or higher
Hb1-2 - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hb1-1 - Hb1-2 Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Front Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Wire LH)


OK

6.CHECK FRONT SEAT WIRE LH

NG

REPLACE FLOOR WIRE

6.CHECK FRONT SEAT WIRE LH
a.
U147039E02
0.323,0.781 0.323,1.042 false 1.01,0.635 1.01,0.292 1.01,0.292 0.844,0.292 false 1.771,0.781 1.771,1.135 false 1.177,2.948 1.438,2.667 true 1.74,2.656 2.021,2.938 true 0.271,1.76 0.438,1.927 0.167,0.167 10 false *a 0.24,1.052 0.396,1.208 0.156,0.156 10 false *1 2.677,0.615 2.854,0.771 0.177,0.156 10 false *2 2.25,0.615 2.365,0.771 0.115,0.156 10 false A 1.948,0.615 2.063,0.771 0.115,0.156 10 false B 1.5,0.615 1.625,0.771 0.125,0.156 10 false C 1.188,0.625 1.313,0.781 0.125,0.156 10 false D 0.74,0.625 0.865,0.781 0.125,0.156 10 false E 0.438,0.625 0.563,0.781 0.125,0.156 10 false F 0.729,2.427 0.906,2.583 0.177,0.156 10 false b1 0.667,0.208 0.823,0.365 0.156,0.156 10 false *3 1.688,1.146 1.844,1.302 0.156,0.156 10 false *4 0.833,2.896 1.208,3.146 0.375,0.25 10 false SFL- 2.073,2.896 2.469,3.125 0.396,0.229 10 false SFL+

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - Body ground Ignition switch ON Below 1 V
b1-2 (SFL+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - b1-2 (SFL+) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - Body ground Always 1 MΩ or higher
b1-2 (SFL+) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (SFL-) - b1-2 (SFL+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Text in Illustration
*1 Front Seat Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Front Seat Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


OK

NG

REPLACE FRONT SEAT ASSEMBLY LH