Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905  Short in P/T Squib (LH) Circuit  B1906  Open in P/T Squib (LH) Circuit  B1907  Short in P/T Squib (LH) Circuit (to Ground)  B1908  Short in P/T Squib (LH) Circuit (to +B)  


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.

The airbag ECU assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1905
·

The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag ECU assembly


B1906
·

The airbag ECU assembly receives an open circuit signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


B1907
·

The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


B1908
·

The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C263726E07
0.495,2.551 0.792,2.688 0.297,0.137 10 H22 4.817,3.02 5.091,3.158 0.273,0.137 10 H17 0.481,2.7 2.702,3.023 2.221,0.323 10 Front Seat Outer Belt Assembly LH (Front Pretensioner LH) 4.803,3.17 6.197,3.316 1.394,0.147 10 Airbag ECU Assembly 2.414,1.069 2.509,1.209 0.096,0.140 10 2 2.414,1.905 2.514,2.045 0.100,0.140 10 1 4.718,1.17 5.061,1.309 0.343,0.139 10 PL+ 4.718,2.01 5.022,2.149 0.304,0.139 10 PL- 4.528,1.069 4.623,1.209 0.096,0.140 10 2 4.529,1.905 4.623,2.045 0.094,0.140 10 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E01
0.637,0.972 0.758,1.125 0.121,0.153 10 D 1.044,0.972 1.164,1.125 0.121,0.153 10 C 1.622,0.972 1.743,1.125 0.121,0.153 10 B 2.025,0.972 2.146,1.125 0.121,0.153 10 A 2.47,0.979 2.646,1.154 0.177,0.175 10 *2 0.45,1.577 0.602,1.730 0.152,0.152 10 *1 0.526,1.119 0.526,1.56 false 1.638,0.473 1.790,0.625 0.152,0.152 10 *3 1.387,0.987 1.387,0.563 1.387,0.563 1.613,0.563 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly LH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)
a.
U147019E02
0.667,0.906 0.667,1.302 false 1.802,2.302 1.979,2.302 false 0.604,1.313 0.76,1.479 0.156,0.167 10 false *1 2.24,0.729 2.406,0.896 0.167,0.167 10 false *2 1.813,0.75 1.979,0.917 0.167,0.167 10 false A 1.646,0.75 1.74,0.917 0.094,0.167 10 false B 1.135,0.75 1.302,0.917 0.167,0.167 10 false C 0.781,0.75 0.896,0.917 0.115,0.167 10 false D 0.469,2.25 0.74,2.427 0.271,0.177 10 false H22 2,2.219 2.313,2.385 0.313,0.167 10 false SST 0.323,1.677 0.479,1.844 0.156,0.167 10 false *a

Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTCs B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U147020E02
0.573,0.792 0.573,0.385 0.573,0.385 0.427,0.385 false 1.375,0.792 1.375,0.385 1.375,0.385 1.229,0.385 false 0.219,0.302 0.375,0.469 0.156,0.167 10 false *1 2.365,0.792 2.531,0.958 0.167,0.167 10 false *2 1.948,0.781 2.073,0.948 0.125,0.167 10 false A 1.573,0.771 1.698,0.938 0.125,0.167 10 false B 1.063,0.771 1.229,0.938 0.167,0.167 10 false C 0.688,0.771 0.792,0.938 0.104,0.167 10 false D 0.354,1.823 0.51,1.99 0.156,0.167 10 false *a 0.646,2.344 0.917,2.521 0.271,0.177 10 false H22 1.063,0.313 1.219,0.479 0.156,0.167 10 false *3

Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H22-1 - Body ground Ignition switch ON Below 1 V
H22-2 - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H22-1 - H22-2 Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H22-1 - Body ground Always 1 MΩ or higher
H22-2 - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H22-1 - H22-2 Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E01
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTCs B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag ECU Assembly



OK

NG