Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2016.06
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297705 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  INSTALLATION  


PROCEDURE

Hide 45130 1.INSTALL HORN BUTTON ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



c.

for Dual Airbag System

i.
B311945E02
1.385,1.708 1.573,1.719 true 1.219,0.427 1.479,0.229 true 2.042,1.979 3.156,1.979 true 1.99,2.292 2.188,2.292 2.188,2.292 2.188,1.979 true 1.198,1.625 1.385,1.781 0.188,0.156 10 false *2 1.521,0.125 1.708,0.281 0.188,0.156 10 false *3 3.167,1.896 3.354,2.052 0.188,0.156 10 false *1

Connect the 2 airbag connectors to the horn button assembly.

Text in Illustration
*1 Airbag Connector
*2 Horn Connector
*3 Airbag Connector Lock

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Be sure to only connect the connectors to each corresponding color.




ii.

Push in the 2 locks to install the 2 airbag connectors.

NOTICE:

Make sure that the horn button assembly is securely installed.



iii.

Connect the horn connector to the horn button assembly.



d.

for Single Airbag System

i.
B311353E02
1.365,1.698 1.542,1.729 true 2.594,0.49 2.354,0.302 true 1.927,2.125 2,2.333 true 1.198,1.604 1.385,1.76 0.188,0.156 10 false *2 2.167,0.177 2.354,0.333 0.188,0.156 10 false *3 1.948,2.354 2.135,2.51 0.188,0.156 10 false *1

Connect the airbag connector to the horn button assembly.

Text in Illustration
*1 Airbag Connector
*2 Horn Connector
*3 Airbag Connector Lock

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



ii.

Push in the lock to install the airbag connector.

NOTICE:

Make sure that the horn button assembly is securely installed.



iii.

Connect the horn connector to the horn button assembly.



e.
B311354

Push the horn button assembly to engage the 3 pins carefully.

NOTICE:
·

Make sure that the pins are securely inserted into the steering holes.

·

Make sure that the horn button assembly is securely installed.




f.

Install the No. 1 and No. 2 lower steering wheel covers.


Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Hide 45130 3.INSPECT HORN BUTTON ASSEMBLY

a.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system (See page Vehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE).