1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Remove the spiral cable with sensor sub-assembly from the vehicle.
(See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL)
Visually check for defects with the spiral cable sub-assembly.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | for Dual Airbag System | *B | for Single Airbag System |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
*b | Color: Orange |
| *c | Color: Black | - | - |
Set the spiral cable sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).
Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-1 - z7-1 | Always | Below 1 Ω |
| D52-2 - z7-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
| D52-4 - z6-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-4 - z6-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-1 - z7-1 | Always | Below 1 Ω |
| D52-2 - z7-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
| D52-4 - z6-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-4 - z6-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-1 - z7-1 | Always | Below 1 Ω |
| D52-2 - z7-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
| D52-4 - z6-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D77-1 - z4-3 | Always | 3 Ω or less |
| D77-2 - z4-4 | Always | 3 Ω or less |
| D77-8 - z4-1 | Always | 3 Ω or less |
| D77-3 - z9-8 | Always | 3 Ω or less |
| D77-4 - z9-9 | Always | 3 Ω or less |
| D77-5 - z9-10 | Always | 3 Ω or less |
| D77-6 - z9-11 | Always | 3 Ω or less |
| D77-9 - z9-1 | Always | 3 Ω or less |
| D77-10 - z9-2 | Always | 3 Ω or less |
| D77-11 - z9-3 | Always | 3 Ω or less |
| D77-12 - z9-4 | Always | 3 Ω or less |
| D77-13 - z9-5 | Always | 3 Ω or less |
| D77-14 - z9-6 | Always | 3 Ω or less |
| D52-4 - z6-2 | Always | Below 1 Ω |
| D52-3 - z6-1 | Always | Below 1 Ω |
If the result is not as specified, replace the spiral cable with sensor sub-assembly.