Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2016.06
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297706 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


PROCEDURE

Hide 45111 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the front wheels are facing straight ahead.


b.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B450360E01
4.167,2.365 4.167,1.688 true 4.219,1.521 4.219,1.281 4.219,1.281 3.594,1.281 true 0.76,2.427 0.76,1.823 true 0.74,1.604 0.74,1.396 0.74,1.396 0.219,1.396 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 0.031,1.281 0.344,1.438 0.313,0.156 10 false *a 0.677,2.438 0.854,2.625 0.177,0.188 10 false *b 4.104,2.375 4.417,2.531 0.313,0.156 10 false *c 3.375,1.125 3.688,1.281 0.313,0.156 10 false *a

Text in Illustration
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -

NOTICE:

If the result is not as specified, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 73900 4.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

Hide 55318C 5.REMOVE INSTRUMENT SIDE PANEL (w/o Knee Airbag)

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55461A 7.REMOVE INSTRUMENT PANEL ORNAMENT (w/ Large Ornament Panel)

Hide 55405B 8.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Large Ornament Panel)

Hide 55422 10.REMOVE UPPER INSTRUMENT PANEL METER ORNAMENT

Hide 45289A 11.REMOVE STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

Hide 12.REMOVE LOWER STEERING COLUMN COVER

Hide 45286 13.REMOVE UPPER STEERING COLUMN COVER

Hide 14.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable sub-assembly without the steering wheel with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B311356E02
0.875,1.792 1.156,1.875 true 1.208,1.781 1.396,1.938 0.188,0.156 10 false *1

Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

Text in Illustration
*1 Slider

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connector from the spiral cable with sensor sub-assembly.


f.
B311363

Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.


Hide 15.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Remove the spiral cable sub-assembly from the steering sensor only when replacing it or the steering sensor.

·

Do not rotate the center section of the steering sensor, as it may deviate from the steering sensor neutral point.



a.
B313958E02
2.094,0.25 2.438,0.667 true 2.073,1.01 2.438,1.156 true 0.771,0.854 1.354,0.5 true 2.917,0.927 3.177,0.688 true 1.927,0.115 2.104,0.344 0.177,0.229 10 false *1 3.198,0.573 3.385,0.729 0.188,0.156 10 false *2 1.396,0.385 1.583,0.542 0.188,0.156 10 false *2 1.917,0.917 2.104,1.073 0.188,0.156 10 false *1

Disengage the 6 claws, 2 pins and 2 guides to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the guide and claw.


Text in Illustration
*1 Guide
*2 Pin