Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297707 KNEE AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a lower No. 1 instrument panel airbag assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the lower No. 1 instrument panel airbag assembly.

·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Do not apply water etc. to a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the lower No. 1 instrument panel airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 73900 2.DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the lower No. 1 instrument panel airbag assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.



b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Remove the instrument side cover (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


d.

Remove the No. 1 instrument panel under cover sub-assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


e.

Disconnect the lower No. 1 instrument panel airbag connector.

i.

Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

SST
09082-18010  
09082-18020  

CAUTION:

Check that there is no looseness in the lower No. 1 instrument panel airbag assembly.


i.
B316993E01
1.282,1.376 0.604,1.376 false 1.302,1.291 1.650,1.452 0.348,0.161 10 SST 1.901,1.179 2.249,1.340 0.348,0.161 10 *a 2.55,1.266 2.083,1.271 false 1.09,1.376 1.09,1.799 false

Connect the clip and terminal of SST.

Text in Illustration
*a Connect the clip and terminal


ii.

Connect the SST connector to the lower No. 1 instrument panel airbag assembly.

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



iii.
B316994E01
1.911,0.841 2.239,1.052 0.328,0.212 10 SST 1.561,0.919 1.902,0.919 false 0.872,1.763 1.058,1.924 0.186,0.161 10 *1 2.076,1.537 2.232,1.716 0.156,0.178 9 *a 0.961,1.482 0.961,1.724 false

Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

Text in Illustration
*1 Battery
*a 10 m (32.8 ft.) or more


iv.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.




g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the clip of SST to the positive (+) battery terminal.


iii.

Connect the terminal of SST to the negative (-) battery terminal to deploy the lower No. 1 instrument panel airbag assembly.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Do not apply water etc. to a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.





Hide 73900 3.DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.

Remove the lower No. 1 instrument panel airbag assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Before removing the lower No. 1 instrument panel airbag assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.




b.
B466517E01
2.313,0.927 2.635,0.375 2.635,0.375 2.438,0.375 false 2.219,0.292 2.531,0.49 0.313,0.198 10 false *1 2.646,1.51 2.958,1.708 0.313,0.198 10 false *a

Using braided wire, tie down the lower No. 1 instrument panel airbag assembly to an unneeded tire.

Text in Illustration
*1 Stripped Wire Section
*a Wire Diameter

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the lower No. 1 instrument panel airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.

Position the lower No. 1 instrument panel airbag assembly inside the tire with the airbag deployment side facing inside.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


B311370E01
1.336,2.358 1.578,2.567 0.242,0.209 10 *a 2.731,1.598 2.972,1.764 0.242,0.166 10 *b

Text in Illustration
*a Width *b Inner Diameter

CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the lower No. 1 instrument panel airbag assembly may break loose when the airbag is deployed.

·

Always tie down the lower No. 1 instrument panel airbag assembly with the airbag deployment side facing inside the tire as shown in the illustration.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




c.

Install SST.

SST
09082-18010  
09082-18020  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.


i.
B311371E01
2.277,0.627 2.572,0.849 0.295,0.222 10 *a 2.902,1.017 2.464,0.763 false 2.295,1.449 1.759,1.449 1.759,1.449 1.635,1.722 false 2.315,1.364 2.663,1.525 0.348,0.161 10 SST 2.103,1.449 2.103,1.722 false

Connect the clip and terminal of SST.

Text in Illustration
*a Connect the clip and terminal


ii.

After connecting the following SST to each other, connect them to the lower No. 1 instrument panel airbag assembly.



d.

Place the tires.

i.
C188679E03
2.671,0.373 2.837,0.54 0.167,0.167 10 *1 2.688,1.437 2.854,1.604 0.167,0.167 10 *1

Place at least 2 tires under the tire to which the lower No. 1 instrument panel airbag assembly is tied.

Text in Illustration
*1 Tires (2 or more)

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheel.




ii.

Place at least 2 tires onto the tire to which the lower No. 1 instrument panel airbag assembly is tied. The top tire should have a wheel installed.


iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




e.
B311372E02
2.667,1.396 1.802,0.292 1.802,0.292 1.49,0.292 true 0.51,2.896 0.51,3.125 false 1.344,2.375 1.115,2.375 false 1.302,0.219 1.49,0.375 0.188,0.156 10 false *1 0.427,3.167 0.615,3.323 0.188,0.156 10 false *2 1.323,3.156 1.51,3.313 0.188,0.156 10 false *a 1.365,2.292 1.708,2.448 0.344,0.156 10 false SST

Deploy the airbag.

Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Battery
*a 10 m (32.8 ft.) or more

i.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the lower No. 1 instrument panel airbag assembly is tied.


iii.

Connect the clip of SST to the positive (+) battery terminal.


iv.

Connect the terminal of SST to the negative (-) battery terminal to deploy lower No. 1 instrument panel airbag assembly.

CAUTION:

Before deployment, make sure that no one is near the airbag.




f.

Dispose of the lower No. 1 instrument panel airbag assembly.

CAUTION:
·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Do not apply water etc. to a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the lower No. 1 instrument panel airbag assembly from the tire.


ii.

Place the lower No. 1 instrument panel airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.