Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM2090E _58 Vehicle Interior _060703 SEAT BELT _0297725 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (for driver).

WIRING DIAGRAM

B314061E03
5.188,1.885 5.417,2.073 0.229,0.188 10 false D7 5.479,0.969 5.656,1.125 0.177,0.156 10 false 37 5.708,1.073 6.115,1.25 0.406,0.177 10 false DBKL 3.292,0.958 3.448,1.104 0.156,0.146 10 false 1 2.385,0.958 2.521,1.125 0.135,0.167 10 false 2 2.323,1.354 2.74,1.521 0.417,0.167 10 false H19*1 2.302,1.51 3.635,1.865 1.333,0.354 10 false Front Seat Inner Belt Assembly (for Driver) 5.177,2.073 7.031,2.271 1.854,0.198 10 false Combination Meter Assembly 2.781,1.354 3.177,1.51 0.396,0.156 10 false G3*2 0.208,2.146 0.927,2.323 0.719,0.177 10 false *1: for LHD 0.198,2.448 0.917,2.625 0.719,0.177 10 false *2: for RHD

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

OK:

Driver side seat belt warning light condition can be switched by Active Test.


Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Driver Side Seat Belt Driver side seat belt warning light ON/OFF -



OK

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)

NG

REPLACE COMBINATION METER ASSEMBLY

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)
a.

Remove the front seat inner belt assembly (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Inspect the front seat inner belt assembly (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the H19 front seat inner belt assembly connector. (for LHD)


b.

Disconnect the G3 front seat inner belt assembly connector. (for RHD)


c.

Disconnect the D7 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
H19-1 - D7-37 (DBKL) Always Below 1 Ω
H19-1 - Body ground Always 10 kΩ or higher
H19-2 - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G3-1 - D7-37 (DBKL) Always Below 1 Ω
G3-1 - Body ground Always 10 kΩ or higher
G3-2 - Body ground Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR