Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1430/21  Open in Room Temperature Sensor Circuit  B1431/-21  Short in Room Temperature Sensor Circuit  


DESCRIPTION

The cooler (room temp. sensor) thermistor is installed in the instrument panel to detect the cabin temperature which is used to control the heater and air conditioning system AUTO mode. The resistance of the cooler (room temp. sensor) thermistor changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning control assembly applies a voltage (5 V) to the cooler (room temp. sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (room temp. sensor) thermistor.

DTC No. DTC Detection Condition Trouble Area
B1430/21 Open in room temperature sensor circuit
·

Cooler (room temp. sensor) thermistor

·

Harness or connector between cooler (room temp. sensor) thermistor and air conditioning control assembly

·

Air conditioning control assembly


B1431/-21 Short in room temperature sensor circuit
·

Cooler (room temp. sensor) thermistor

·

Harness or connector between cooler (room temp. sensor) thermistor and air conditioning control assembly

·

Air conditioning control assembly



WIRING DIAGRAM

E248910E02
4.635,1.365 4.875,1.531 0.24,0.167 10 false SG 4.448,1.271 4.563,1.438 0.115,0.167 10 false 6 0.333,1.958 3.469,2.146 3.135,0.188 10 false COOLER (ROOM TEMP. SENSOR) THERMISTOR 4.635,0.927 4.865,1.094 0.229,0.167 10 false TR 4.458,0.833 4.563,0.99 0.104,0.156 10 false 5 0.344,1.792 0.615,1.958 0.271,0.167 10 false D67 2.365,0.823 2.5,1 0.135,0.177 10 false 1 2.375,1.26 2.49,1.406 0.115,0.146 10 false 2 3.938,2.208 6.708,2.385 2.771,0.177 10 false AIR CONDITIONING CONTROL ASSEMBLY 3.938,2.042 4.208,2.208 0.271,0.167 10 false D20

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Room Temperature Sensor
(Room Temp)
Room Temperature Sensor /
min.: -72.47°C (-98.4°F)
max.: 193.82°C (380.9°F)
Actual cabin temperature displayed -

OK:

The display is as specified in the normal condition column.


Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C




A

2.CHECK FOR DTC

B

C

3.INSPECT COOLER (ROOM TEMP. SENSOR) THERMISTOR
3.INSPECT COOLER (ROOM TEMP. SENSOR) THERMISTOR
a.

Remove the cooler (room temp. sensor) thermistor (See page Vehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>REMOVAL).


b.

Inspect the cooler (room temp. sensor) thermistor (See page Vehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMP. SENSOR) THERMISTOR - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPLACE COOLER (ROOM TEMP. SENSOR) THERMISTOR

4.CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMP. SENSOR) THERMISTOR - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the D20 air conditioning control assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D67-1 - D20-5(TR) Always Below 1 Ω
D67-2 - D20-6(SG) Always Below 1 Ω
D67-1 - Body ground Always 10 kΩ or higher
D67-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR