Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1436/45  Open in Passenger Side Air Mix Damper Position Sensor Circuit  B1437/-45  Short in Passenger Side Air Mix Damper Position Sensor Circuit  B1441/E45  Passenger Side Air Mix Damper Control Servomotor Circuit  


DESCRIPTION

This sensor detects the position of the air mix damper and sends appropriate signals to the A/C amplifier assembly. The position sensor is built into the air mix control servo motor. This adjusts the amount of air passing through the heater core after passing the No. 1 cooler evaporator sub-assembly and controls the temperature of the output air.

HINT:

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


E109300E01
0.223,0.186 0.962,0.349 0.739,0.163 10 Voltage (V) 0.868,2.91 2.315,3.073 1.448,0.163 10 Damper opening angle 0.773,0.977 0.936,1.147 0.163,0.170 10 4 0.765,1.982 0.914,2.166 0.149,0.184 10 1 0.945,2.472 1.087,2.614 0.142,0.142 10 0 2.251,2.472 2.678,2.614 0.427,0.142 10 100%

DTC No. DTC Detection Condition Trouble Area
B1436/45 Open in passenger side air mix damper position sensor circuit
·

No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))

·

Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.

·

Air conditioning control assembly


B1437/-45 Short in passenger side air mix damper position sensor circuit
·

No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))

·

Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.

·

Air conditioning control assembly


B1441/E45 Passenger side air mix damper control servomotor circuit
·

No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side))

·

Harness or connector between No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) and air conditioning control assembly.

·

Air conditioning control assembly



WIRING DIAGRAM

E248914E04
4.844,1.771 6.76,2.292 1.917,0.521 10 false No. 4 Air Conditioning Radiator Damper Servo Sub-assembly (Air Mix(for Passenger Side)) 2.083,1.073 2.448,1.26 0.365,0.188 10 false TPPa 1.948,0.271 2.448,0.438 0.5,0.167 10 false AMHPa 1.948,0.677 2.438,0.854 0.49,0.177 10 false AMCPa 4.844,1.583 5.125,1.74 0.281,0.156 10 false A28 2.229,1.875 2.427,2.063 0.198,0.188 10 false SG 2.573,1.781 2.667,1.927 0.094,0.146 10 false 6 0.719,2.229 2.823,2.406 2.104,0.177 10 false Air Conditioning Control Assembly 2.24,1.479 2.427,1.646 0.188,0.167 10 false S5 2.531,1.396 2.719,1.552 0.188,0.156 10 false 13 2.573,1 2.688,1.156 0.115,0.156 10 false 3 2.531,0.198 2.719,0.354 0.188,0.156 10 false 11 2.531,0.604 2.719,0.76 0.188,0.156 10 false 12 5.167,0.781 5.292,0.927 0.125,0.146 10 false 5 5.167,0.198 5.281,0.354 0.115,0.156 10 false 7 5.167,0.49 5.281,0.646 0.115,0.156 10 false 6 5.167,1.052 5.281,1.219 0.115,0.167 10 false 1 5.177,1.344 5.281,1.5 0.104,0.156 10 false 3 0.563,2.021 0.833,2.177 0.271,0.156 10 false D20 5.344,0.771 5.552,0.927 0.208,0.156 10 false TP 5.344,0.188 5.677,0.333 0.333,0.146 10 false HOT 5.344,0.479 5.781,0.635 0.438,0.156 10 false COOL 5.344,1.052 5.563,1.198 0.219,0.146 10 false VZ 5.354,1.344 5.688,1.5 0.333,0.156 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

This DTC is stored even for damper link and damper lock, etc. Prior to inspection, confirm that there are no parts with mechanical problems.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Operate the front passenger side temperature adjustment switch.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.


Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Mix Damper Position
A/M Damp Pos-P)
Passenger side air mix damper position /
Min.: -32.68%, Max.: 133.33%
MAX. COLD: 0%
MAX. HOT: 110%
-
Air Mix Damper Target(P) Passenger side air mix damper target position /
Min.: -32.68%, Max.: 133.33%
MAX. COLD: 0%
MAX. HOT: 110%
-


OK

2.CHECK FOR DTC

NG

3.CHECK HARNESS AND CONNECTOR (NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the D20 air conditioning control assembly.


b.

Disconnect the A28 No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)).


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance
Tester Connection Condition Specified Condition
A28-1(VZ) - D20-13(S5) Always Below 1Ω
A28-3(GND) - D20-6(SG) Always Below 1Ω
A28-5(TP) - D20-3(TPPa) Always Below 1Ω
A28-6(COOL) - D20-12(AMCPa) Always Below 1Ω
A28-7(HOT) - D20-11(AMHPa) Always Below 1Ω
A28-1(VZ) - Body ground Always 10 kΩ or higher
A28-3(GND) - Body ground Always 10 kΩ or higher
A28-5(TP) - Body ground Always 10 kΩ or higher
A28-6(COOL) - Body ground Always 10 kΩ or higher
A28-7(HOT) - Body ground Always 10 kΩ or higher


OK

4.INSPECT NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.INSPECT NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.

Remove the No. 4 air conditioning radiator damper servo sub-assembly (air mix (for front passenger side)) (See pageVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).


b.

Potentiometer circuit inspection

i.
U190444E02
2.25,0.708 1.854,1.385 true 2.594,1.844 2.094,1.469 true 1.177,0.49 1.552,1.385 true 1.052,1.865 1.427,1.469 true 0.729,0.948 1.313,1.396 true 1.542,0.427 1.833,0.583 0.292,0.156 10 false A28 2.302,0.615 2.625,0.792 0.323,0.177 10 false GND 2.646,1.771 2.844,1.948 0.198,0.177 10 false VZ 0.938,0.417 1.135,0.594 0.198,0.177 10 false TP 0.625,1.802 1.021,1.969 0.396,0.167 10 false COOL 0.354,0.875 0.667,1.052 0.313,0.177 10 false HOT 0.177,0.156 0.344,0.344 0.167,0.188 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Condition Specified Condition
A28-1(VZ) - A28-3(GND) Always 4.2 to 7.8 kΩ

Text in Illustration
*a Component without harness connected
(No. 4 air Conditioning radiator damper servo sub-assembly)


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance
Tester Connection Condition Specified Condition
A28-1(VZ) - A28-5(TP) MAX. COOL position 3.4 to 6.2 kΩ
A28-1(VZ) - A28-5(TP) MAX. HOT position 0.8 to 1.6 kΩ

E249948E01
3.417,0.152 4.236,0.513 0.819,0.361 10 *B 0.2,0.152 1.019,0.513 0.819,0.361 10 *A 1.842,3.122 2.018,3.283 0.175,0.161 10 *b 0.862,1.187 1.058,1.365 0.196,0.177 10 *a 3.8,2.313 3.988,2.467 0.188,0.154 10 *b 5.348,0.503 5.507,0.661 0.159,0.158 10 *a

Text in Illustration
*A for LHD
*B for RHD
*a MAX. HOT
*b MAX. COOL


iii.
E108925E17
2.292,2.927 3.135,3.094 0.844,0.167 10 false Arm Position 0.198,1.354 0.833,1.521 0.635,0.167 10 false 3.4 to 6.2 0.208,2.354 0.844,2.531 0.635,0.177 10 false 0.8 to 1.6 1.042,2.635 1.844,2.802 0.802,0.167 10 false MAX. COOL 2.448,2.625 3.146,2.802 0.698,0.177 10 false MAX. HOT 0.188,0.531 1.219,0.719 1.031,0.188 10 false Resistance (kΩ)

As the arm of the air mix control servo motor moves from the COOL side to the HOT side, the resistance decreases gradually without interruption.



c.

Motor circuit inspection

i.

When the terminal 6 (COOL) of the connector A28 is connected to the battery positive terminal, and terminal 7 (HOT) of the connector A28 is connected to the battery negative terminal, confirm that the arm smoothly rotates from HOT to COOL.

HINT:

Because the arm does not automatically stop at servo unit inspection, at inspection, turn off the power supply near COOL



ii.

When the terminal 7 (HOT) of the connector A28 is connected to the battery positive terminal, and terminal 6 (COOL) of the connector A28 is connected to the battery negative terminal, confirm that the arm smoothly rotates from COOL to HOT.

HINT:

Because the arm does not automatically stop at servo unit inspection, at inspection, turn off the power supply near HOT.





OK

NG

REPLACE NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)