Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A1/25  Open in Solar Sensor Circuit  B14A2/-25  Short in Solar Sensor Circuit  


DESCRIPTION

E107008E54
0.583,0.094 2.167,0.26 1.583,0.167 10 false Resistance of Photodiode 0.531,0.708 0.833,0.896 0.302,0.188 10 false High 0.563,2.229 0.854,2.406 0.292,0.177 10 false Low 0.979,2.563 1.385,2.74 0.406,0.177 10 false Weak 2.385,2.563 2.833,2.76 0.448,0.198 10 false Strong 0.948,2.885 2.604,3.063 1.656,0.177 10 false Strength of Solar Radiation

The automatic light control sensor is installed on the upper side of the instrument panel. It detects sunlight to control air conditioning AUTO mode. The output voltage from the automatic light control sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning control assembly detects changes in the output voltage from the automatic light control sensor.

DTC No. DTC Detection Condition Trouble Area
B14A1/25 Open in Solar Sensor Circuit
·

Automatic light control sensor

·

Harness or connector between automatic light control sensor and air conditioning control assembly

·

Harness or connector between automatic light control sensor and main body ECU (network gateway body ECU)

·

Main body ECU (network gateway body ECU)

·

Air conditioning control assembly


B14A2/-25 Short in Solar Sensor Circuit
·

Automatic light control sensor

·

Harness or connector between automatic light control sensor and air conditioning control assembly

·

Harness or connector between automatic light control sensor and main body ECU (network gateway body ECU)

·

Main body ECU (network gateway body ECU)

·

Air conditioning control assembly



WIRING DIAGRAM

E249945E02
0.563,2.292 2.469,2.479 1.906,0.188 10 false Automatic Light Control Sensor 2.292,0.615 2.385,0.76 0.094,0.146 10 false 3 2.292,0.198 2.385,0.344 0.094,0.146 10 false 6 2.302,1.771 2.396,1.917 0.094,0.146 10 false 1 0.563,2.125 0.833,2.281 0.271,0.156 10 false D45 4.01,0.635 4.188,0.781 0.177,0.146 10 false 15 4.01,0.208 4.188,0.354 0.177,0.146 10 false 13 4.083,1.208 6.604,1.396 2.521,0.188 10 false Main Body ECU (Network Gateway ECU) 4.094,1.042 4.302,1.198 0.208,0.156 10 false D6 4.26,1.875 4.625,2.052 0.365,0.177 10 false CLTS 4.083,1.781 4.177,1.927 0.094,0.146 10 false 2 4.083,2.167 4.365,2.333 0.281,0.167 10 false D20 4.073,2.323 6.177,2.531 2.104,0.208 10 false Air Conditioning Control Assembly 1.865,0.292 2.229,0.458 0.365,0.167 10 false CLTE 1.865,0.719 2.229,0.885 0.365,0.167 10 false CLTB 1.938,1.875 2.229,2.042 0.292,0.167 10 false TSD 4.24,0.292 4.625,0.458 0.385,0.167 10 false CLTE 4.24,0.719 4.615,0.896 0.375,0.177 10 false CLTB

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor Solar sensor /
Min.: 0W/m2
Max.: 4448W/m2
Solar sensor value increases as brightness increases -

OK:

The display is as specified in the Normal Condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U190424E02
0.906,2.729 1.427,2.5 true 1.885,2.781 2.458,2.5 true 0.281,0.26 0.469,0.427 0.188,0.167 10 false *a 1.563,0.896 1.833,1.063 0.271,0.167 10 false D45 2.5,2.417 2.865,2.583 0.365,0.167 10 false CLTE 0.5,2.677 0.865,2.865 0.365,0.188 10 false CLTB

Disconnect the D45 solar automatic light control sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D45-6(CLTE) - D45-3(CLTB) Ignition switch off Below 1 V
D45-6(CLTE) - D45-3(CLTB) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Automatic Light Control Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the D45 automatic light control sensor connector.


b.

Disconnect the D20 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D20-2(CLTS) - D45-1(TSD) Always Below 1 Ω
D20-2(CLTS) - Body ground Always 10 kΩ or higher




OK

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
U190425E02
2.01,1.365 2.76,0.938 true 2.021,1.625 2.76,2.021 true 0.25,0.281 0.438,0.469 0.188,0.188 10 false *a 1.656,0.385 1.927,0.552 0.271,0.167 10 false D45 2.813,0.854 3.104,1.042 0.292,0.188 10 false TSD 2.802,1.958 3.177,2.135 0.375,0.177 10 false CLTB

Remove the automatic light control sensor (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Reconnect the D45 automatic light control sensor connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D45-1(TSD) - D45-3(CLTB) Sensor is subjected to electric light 0.8 to 4.3 V
D45-1(TSD) - D45-3(CLTB) Sensor is covered with a cloth Below 0.8 V

Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)


NOTICE:
·

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 2 and the positive (+) lead to terminal 6 of the automatic light control sensor.

·

Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the automatic light control sensor.

·

As the inspection light is moved away from the sensor, the voltage decreases.





OK

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D6-13(CLTE) - D45-6(CLTE) Always Blow 1 Ω
D6-15(CLTB) - D45-3(CLTB) Always Blow 1 Ω
D6-13(CLTE) - Body ground Always 10 kΩ or higher
D6-15(CLTB) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR