Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297739 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 88326A 1.INSTALL COVER PLATE

a.
E252254

Install the cover plate.


Hide 88521B 2.INSTALL COOLER UNIT CASE PACKING (for Automatic Air Conditioning System)

a.
E250764

Install the cooler unit case packing.


Hide 88521B 3.INSTALL COOLER UNIT CASE PACKING (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88544 4.INSTALL COOLER BLOWER CASE

a.

Install the cooler blower case from the lower heater case.


b.
E246469

Engage the 2 claws.


c.

Install the blower case assembly with the 4 screws.


Hide 87165C 5.INSTALL BLOWER MOTOR CONTROL (for Automatic Air Conditioning System)

a.
E250761

Install the blower motor control with the 2 screws.


Hide 87138C 6.INSTALL BLOWER RESISTOR (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87138C 7.INSTALL BLOWER RESISTOR (w/o Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88710 8.INSTALL AIR CONDITIONER TUBE ASSEMBLY (for Automatic Air Conditioning System)

a.
E250774

Using a 4 mm hexagon wrench, install the air conditioner tube assembly with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 88710 9.INSTALL AIR CONDITIONER TUBE ASSEMBLY (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88625 10.INSTALL NO. 1 COOLER THERMISTOR (for Automatic Air Conditioning System)

Hide 88625 11.INSTALL NO. 1 COOLER THERMISTOR (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88899P 12.INSTALL COVER PLATE (w/o Air Conditioning System)

a.

Install the cover plate.


Hide 88501 13.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E250759

Install the No. 1 cooler evaporator sub-assembly with evaporator pipe as a unit.


Hide 88501 14.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88502A 15.INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E246468

Engage the 2 claws.


b.

Install the cooling unit case sub-assembly with the 7 screws.


c.
E250758

Engage the clamp.


Hide 88502A 16.INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88502A 17.INSTALL COOLING UNIT CASE SUB-ASSEMBLY (w/o Air Conditioning System)

a.
E246468

Engage the 2 claws.


b.

Install the cooling unit case sub-assembly with the 7 screws.


Hide 55906 18.INSTALL HEATER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

NOTICE:
·

When working, take care not to get dirt or dust in the gear grease.

·

Do not hold gear sections while wearing cotton work gloves.



a.
E254919

Turn the pin on the cable side as far as possible in the direction of the arrow, and position it so that it matches the hole in the gear.

HINT:

Set the temperature adjustment dial to MAX HOT.



b.
E254922E01
2.939,1.689 3.120,1.866 0.181,0.177 10 *2 0.361,1.683 0.542,1.860 0.181,0.177 10 *1 0.616,0.775 0.463,1.647 0.463,1.647 1.137,1.194 false 2.477,1.156 3.006,1.665 3.006,1.665 2.957,0.77 false

Hold the protrusion on the drive gear, and rotate the gear until the protrusion is aligned with the cylindrical section of the case.

Text in Illustration
*1 Drive gear hole
*2 Control cable positioning pin

HINT:

Temperature adjustment dial: MAX HOT



c.

Push the control cable positioning pin in slowly until it matches the drive gear hole, and install the heater control cable sub-assembly.


d.

Replacing the drive gear.

i.
E246474E01
2.911,0.545 3.075,0.709 0.164,0.164 10 *2 3.07,1.937 3.263,2.103 0.193,0.166 10 *d 3.105,2.688 3.298,2.853 0.193,0.166 10 *c 2.015,3.136 2.208,3.302 0.193,0.166 10 *b 1.458,1.152 1.651,1.318 0.193,0.166 10 *a 0.436,0.749 0.600,0.913 0.164,0.164 10 *1 0.617,0.833 0.997,0.646 false 1.454,0.659 1.536,1.132 false 2.897,0.663 2.467,0.94 false 2.426,2.733 2.166,3.128 2.166,3.128 2.164,3.132 false 2.587,2.755 3.088,2.787 false 3.058,2.049 2.514,2.341 false

When replacing the drive gear, pull the resin portion of the control cable forward slowly and remove it.

Text in Illustration
*1 Shaft Gear
*2 Drive Gear
*a Reference Position
*b Drive gear protrusion
*c Cylindrical section of the case
*d Resin portion of the control cable

NOTICE:

Do not pull the drive gear.



ii.

Pull the drive gear forward slowly and remove it.


iii.

Rotate the shaft gear clockwise slowly until it stops.

NOTICE:

Be sure not to turn too forcefully.



iv.

Match the shaft gear and the drive gear with their specified positions, and insert the drive gear slowly into the heater case.



Hide 55906 19.INSTALL HEATER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 55908A 20.INSTALL AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

NOTICE:
·

When working, take care not to get dirt or dust in the gear grease.

·

Do not hold gear sections while wearing cotton work gloves.



a.
E254920

Turn the pin on the cable side as far as possible in the direction of the arrow, and position it so that it matches the hole in the gear.

HINT:

Set the blower dial to FACE.



b.
E254921E01
2.799,0.21 2.992,0.376 0.193,0.166 10 *2 0.736,0.21 0.930,0.376 0.193,0.166 10 *1 0.946,1.397 0.82,0.411 0.82,0.411 1.167,1.243 false 2.476,1.253 2.862,0.409 2.862,0.409 2.699,1.396 false

Hold the protrusion on the drive gear, and rotate the gear clockwise until it stops.

Text in Illustration
*1 Drive gear hole
*2 Control cable positioning pin

HINT:

Temperature control position: VENT



c.

Push the control cable positioning pin in slowly until it matches the drive gear hole, and install the air inlet damper control cable sub-assembly.


d.

Replacing the drive gear.

i.
E246472E01
3.102,2.551 3.266,2.715 0.164,0.164 10 *c 2.146,3.197 2.309,3.361 0.164,0.164 10 *b 1.436,1.164 1.600,1.327 0.164,0.164 10 *a 2.918,0.74 3.081,0.904 0.164,0.164 10 *2 0.4,0.823 0.564,0.987 0.164,0.164 10 *1 1.848,3.071 2.118,3.27 false 2.566,2.999 3.106,2.693 false 0.594,0.88 1.013,0.559 false 2.899,0.841 2.474,0.986 false 1.658,0.781 1.536,1.171 false

When replacing the drive gear, pull the resin portion of the control cable forward slowly and remove it.

Text in Illustration
*1 Mode Main Link
*2 Drive Gear
*a Reference Position
*b Drive gear protrusion
*c Resin portion of the control cable

NOTICE:

Do not pull the drive gear.



ii.

Pull the drive gear forward slowly and remove it.


iii.

Match the mode main link and the drive gear with their specified positions, and insert the drive gear slowly into the heater case.



Hide 55908A 21.INSTALL AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87050E 22.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E250768

Align the link pin and the main link groove, and install the No. 3 air conditioner radiator damper servo sub-assembly with the three screws.


Hide 87050F 23.INSTALL NO. 4 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E250767

Install the No. 4 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 87201B 24.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E246467

Install the No. 2 air duct sub-assembly with the 3 screws.


Hide 87103B 25.INSTALL BLOWER MOTOR WITH FAN SUB-ASSEMBLY

a.
E250755

Install the blower motor with fan sub-assembly with the 3 screws.


Hide 87201 26.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

a.
E250754

Install the No. 1 air duct sub-assembly with the 2 screws.


Hide 88539 27.INSTALL NO. 1 COOLER UNIT DRAIN HOSE

a.
U190458E02
3.031,1.469 3.031,1.073 3.031,1.073 3.156,1.073 false 3.063,1.563 3.063,1.792 3.063,1.792 2.896,1.792 true 2.448,2 2.594,2 2.594,2 2.594,1.635 false 2.25,1.906 2.417,2.073 0.167,0.167 10 false *2 2.021,1.469 2.208,1.635 0.188,0.167 10 false *b 2.719,1.708 2.906,1.875 0.188,0.167 10 false *a 3.167,1 3.333,1.167 0.167,0.167 10 false *1

Install the No. 1 cooler unit drain hose as shown in the illustration.

Text in Illustration
*1 Case
*2 Hose
*a Rib
*b Notched section

HINT:

Align the notched section of the hose with the rib on the case.



Hide 88482A 28.INSTALL COVER

a.
E250752

Engage the 2 claws.


b.

Install the cover with the 3 screws.


Hide 88515 29.INSTALL COOLER EXPANSION VALVE (for Automatic Air Conditioning System)

a.
E250766

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

Compressor oil:
for HFC-134a (R134a):

ND-OIL 8 or equivalent

for HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



b.
E250765

Using a 4 mm hexagon wrench, install the cooler expansion valve with packing with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


c.
E250751

Install the new gasket.


Hide 88515 30.INSTALL COOLER EXPANSION VALVE (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 88521C 31.INSTALL COOLING UNIT CASE

a.
E252240

Engage the 4 claws.


b.

Install the cooling unit case with the 2 screws.


Hide 87139C 32.INSTALL CLEAN AIR FILTER

a.
E250788

Install the clean air filter as shown in the illustration.


Hide 88548B 33.INSTALL AIR FILTER CASE

a.
E250748

Engage the 2 claws to install the air filter case.


Hide 87107A 34.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E250783

Install the heater radiator unit sub-assembly as shown in the illustration.


b.
E250746

Install the clamp with the screw.


Hide 87107A 35.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87107A 36.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY (w/o Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87114B 37.INSTALL HEATER COVER (for Automatic Air Conditioning System)

a.
E250745

Install the heater cover with the 3 screws.


Hide 87114B 38.INSTALL HEATER COVER (for Manual Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87114B 39.INSTALL HEATER COVER (w/o Air Conditioning System)

HINT:

Use the same procedure as for the automatic air conditioning system.


Hide 87050G 40.INSTALL NO. 5 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
E246476E02
0.958,0.656 1.25,0.552 true 0.771,0.844 0.813,1.208 true 0.625,0.802 0.417,1.083 true 2.604,0.635 2.396,0.833 false 1.854,0.344 2.042,0.729 true 1.281,0.448 1.438,0.615 0.156,0.167 10 false *1 1.74,0.146 1.896,0.313 0.156,0.167 10 false *2 0.26,1.083 0.448,1.25 0.188,0.167 10 false *a 0.76,1.229 0.896,1.406 0.135,0.177 10 false A 2.26,0.854 2.396,1.031 0.135,0.177 10 false B

Turn the air mix shaft slowly in the direction of the arrow until it stops.

Text in Illustration
*1 Air Mix Shaft
*2 Drive Gear
*a Reference Position

NOTICE:

Be sure not to turn the air mix shaft too strongly.



b.

Turn the mix shaft so that section A of the air mix shaft matches the reference position of the case.


c.

Match the air mix damper server gear B section and the shaft gear A section.


d.

Install the No. 5 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 87050C 41.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.
E246477E02
1.094,0.927 1.375,1.094 false 0.719,0.385 0.792,0.771 true 0.865,0.885 0.417,0.969 true 2.656,0.917 2.313,0.875 false 2.333,0.354 2.229,0.604 false 1.417,1.042 1.583,1.219 0.167,0.177 10 false *1 2.292,0.125 2.458,0.302 0.167,0.177 10 false *2 0.625,0.177 0.813,0.365 0.188,0.188 10 false *a 0.25,0.927 0.385,1.094 0.135,0.167 10 false A 2.156,0.802 2.292,0.969 0.135,0.167 10 false B

Turn the air mix shaft slowly in the direction of the arrow until it stops.

Text in Illustration
*1 Air Mix Shaft
*2 Drive Gear
*a Reference Position

NOTICE:

Be sure not to turn the air mix shaft too strongly.



b.

Turn the mix shaft so that section A of the air mix shaft matches the reference position of the case.


c.

Match the air mix damper server gear B section and the shaft gear A section.


d.

Install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 88897A 42.INSTALL ASPIRATOR PIPE (for Automatic Air Conditioning System)

a.
E250773

Install the aspirator pipe.


Hide 88897P 43.INSTALL ASPIRATOR (for Automatic Air Conditioning System)

a.
E250772E02
2.313,0.531 2.313,0.635 2.313,0.635 2.594,0.635 true 2.656,0.552 2.802,0.729 0.146,0.177 10 false A

Engage the 2 claws and align the section A with the case side pin, and then install the aspirator and aspirator pipe as one unit.