Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297747 FRONT EVAPORATOR TEMPERATURE SENSOR A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.
E250743E03
0.885,2.76 0.719,3.031 true 0.885,2.521 1.177,2.521 1.177,2.521 1.177,3.042 true 0.719,2.25 0.719,2.167 0.719,2.167 0.458,2.167 true 0.729,2.042 0.729,1.865 0.729,1.865 0.458,1.865 true 1.094,0.635 1.271,0.635 1.271,0.635 1.271,0.802 false 1.271,1.292 0.49,1.229 true 1.542,1.198 2.208,1.063 true 2.26,0.979 2.417,1.135 0.156,0.156 10 false *1 0.292,1.167 0.448,1.323 0.156,0.156 10 false *2 1.104,3.052 1.26,3.208 0.156,0.156 10 false *c 0.26,2.073 0.417,2.229 0.156,0.156 10 false *b 0.26,1.781 0.417,1.938 0.156,0.156 10 false *a 0.563,3.052 0.719,3.208 0.156,0.156 10 false *3 1.5,0.427 1.615,0.604 0.115,0.177 10 false X 0.958,0.552 1.073,0.719 0.115,0.167 10 false a

Install the No. 1 cooler thermistor as shown in the illustration.

Part Length
*a 34.3 mm
*b 27.6 mm
*c 50 mm

Text in Illustration
*1 Sensor Part
*2 Fixed Part
*3 from Tank

NOTICE:
·

Be sure to insert the thermistor only once because reinserting it will not allow it to be firmly secured.

·

When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the thermistor, do not apply excessive force to the wire.

·

Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".




Hide 88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 88502A 4.INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Automatic Air Conditioning System)

Hide 88502A 5.INSTALL COOLING UNIT CASE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55906 7.INSTALL HEATER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55908A 8.INSTALL AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 88897A 9.INSTALL ASPIRATOR PIPE (for Automatic Air Conditioning System)

Hide 88897P 10.INSTALL ASPIRATOR (for Automatic Air Conditioning System)

Hide 87010 11.INSTALL AIR CONDITIONING UNIT ASSEMBLY (for Automatic Air Conditioning System)

Hide 87010 12.INSTALL AIR CONDITIONING UNIT ASSEMBLY (for Manual Air Conditioning System)

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)