Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297763 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the LHD and RHD vehicle.


PROCEDURE

Hide 71470S 1.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH

Hide 71460S 2.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913 4.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the luggage compartment trim cover LH.


Hide 62311B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 64722 7.DISCONNECT LUGGAGE COMPARTMENT INNER TRIM COVER LH

Hide 64721 8.DISCONNECT LUGGAGE COMPARTMENT INNER TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64715D 9.REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

Hide 64714D 10.REMOVE LUGGAGE COMPARTMENT TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 62606A 11.REMOVE QUARTER TRIM LID SUB-ASSEMBLY LH

Hide 62605Q 12.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62462A 13.REMOVE REAR WINDOW SIDE GARNISH LH

Hide 62461A 14.REMOVE REAR WINDOW SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64330 15.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 64811 16.REMOVE BACK WINDOW GLASS

a.
B309176E02
2.229,0.438 1.802,0.844 false 1.656,0.885 1.823,1.042 0.167,0.156 10 false *1

Apply protective tape to the installation position of the back window glass on the vehicle body.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the vehicle body to prevent it from being scratched.



b.
B187142E07
2.396,0.385 2.198,0.615 false 2.938,0.667 2.938,0.802 false 0.938,1 0.792,1.313 false 1.573,1.188 1.406,1.313 false 2.427,0.26 2.708,0.438 0.281,0.177 10 false *a 2.865,0.823 3.208,1.01 0.344,0.188 10 false *1 1.219,1.26 1.448,1.448 0.229,0.188 10 false *2 0.625,1.302 0.854,1.479 0.229,0.177 10 false *3

Using a knife, cut off the moulding, as shown in the illustration.

Text in Illustration
*1 Body
*2 Moulding
*3 Back Window Glass
*a Cut

NOTICE:
·

Do not damage the vehicle body with the knife.

·

If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the back window glass.




c.
B309177E03
2.073,0.76 1.771,0.76 true 1.771,0.5 1.927,0.5 1.927,0.5 1.927,0.75 true 2.115,0.667 2.271,0.813 0.156,0.146 10 false *a

Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.

Text in Illustration
*a Matchmark

HINT:

Matchmarks are not needed to be placed if the back window glass will not be reused.



d.

Disconnect the connector.


e.
B309179E02
2.104,1.365 1.865,1.563 false 0.906,0.594 1.729,0.979 true 1.729,0.979 2.531,0.594 true 1.656,1.01 1.813,1.167 0.156,0.156 10 false *1 2.094,1.24 2.25,1.396 0.156,0.156 10 false *2

Pass a piano wire between the vehicle body and back window glass from the interior.

Text in Illustration
*1 Back Window Glass Stopper
*2 Piano Wire


f.

Tie both wire ends to wooden blocks or similar objects.


g.

Cut off the adhesive by pulling the piano wire around the back window glass.

NOTICE:
·

When separating the back window glass, take care not to damage the paint or interior and exterior ornaments.

·

To prevent the package tray from being scratched when removing the back window glass, place a plastic sheet between the piano wire and package tray.




h.
B309180E01
2.202,1.498 2.354,1.656 0.152,0.158 10 *1 1.808,1.425 2.166,1.589 false

Using suction cups, disengage the windshield glass stoppers and remove the back window glass.

Text in Illustration
*1 Back Window Glass Stopper

NOTICE:
·

There are 2 back window glass stoppers on the back window glass, as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.

·

To prevent the back window glass from dropping when performing this operation, be sure to hold the back window glass using suction cups.




Hide 64813D 17.REMOVE BACK WINDOW GLASS ADHESIVE DAM

a.
B309181E02
0.906,1.427 0.542,1.427 true 0.75,1.438 0.75,1.74 true 2.469,0.781 2.802,0.781 true 2.573,0.771 2.573,0.427 true 0.958,1.344 1.115,1.51 0.156,0.167 10 false *1 2.281,0.708 2.438,0.875 0.156,0.167 10 false *1 0.073,0.135 0.229,0.302 0.156,0.167 10 false *a

Using a scraper, remove the back window glass adhesive dam.

Text in Illustration
*1 Back Window Glass Adhesive Dam
*a Back Side

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the back window glass adhesive dam with a new one.




Hide 75571G 18.REMOVE NO. 1 BACK WINDOW MOULDING

a.
B309182E02
1.719,0.792 1.719,0.365 true 0.115,0.146 0.271,0.292 0.156,0.146 10 false *a 1.646,0.823 1.802,0.969 0.156,0.146 10 false *1

Using a scraper, remove the No. 1 back window moulding.

Text in Illustration
*1 No. 1 Back Window Moulding
*a Back Side

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the No. 1 back window moulding with a new one.




Hide 64811 19.CLEAN BACK WINDOW GLASS

a.

Using a scraper, remove the adhesive tape and adhesive sticking to the back window glass.

NOTICE:

Be careful not to damage the back window glass.



b.
B187131

Clean the outer circumference of the back window glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Even if using new glass, clean it with a non-residue solvent.




Hide 20.CLEAN VEHICLE BODY

a.

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.


B309172E02
1.833,0.656 2.344,0.51 false 2.396,0.427 2.583,0.604 0.188,0.177 10 false *1 4.427,1.563 4.615,1.74 0.188,0.177 10 false a

Standard Dimension:
Area Dimension
a 2.0 mm (0.0787 in.)


Text in Illustration
*1 Body - -
V100145

Adhesive - -


ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.