1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
55409F
3.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
55408F
4.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
62212
5.REMOVE FRONT PILLAR GARNISH LH
62211
6.REMOVE FRONT PILLAR GARNISH RH
67914
7.REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 6 claws and remove the front door scuff plate LH.
67913
8.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62312B
9.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
62311B
10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
11.REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board LH.
62111C
12.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
73220
13.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH
73210
14.SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure described for the LH side.
71470S
15.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH
71460S
16.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH
64722
17.REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH
Fold down the bench type rear seatback assembly.
Disengage the 2 clips and disconnect the luggage compartment inner trim cover LH.
64721
18.REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH
Use the same procedure described for the LH side.
64715D
19.REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
Pull up the rear seatback assembly.
Remove the clip.
Disengage the 8 clips and remove the luggage compartment trim cover LH.
64714D
20.REMOVE LUGGAGE COMPARTMENT TRIM COVER RH
Use the same procedure described for the LH side.
62606A
21.REMOVE QUARTER TRIM LID SUB-ASSEMBLY LH
Along the arrow in the illustration, disengage the 6 claws.
Disengage the 2 clips and 2 guides.
Make the quarter trim lid sub-assembly LH hang down from the lid cover clip.
Push the lid cover clip knobs in the direction of the arrow to remove the 2 lid cover clips along with the quarter trim lid sub-assembly LH.
| *1 | Lid Cover Clip |
Remove the 2 lid cover clips from the lid cover LH.
If there is any damage, be sure to replace the lid cover clip with a new one.
62605Q
22.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
62462A
23.REMOVE REAR WINDOW SIDE GARNISH LH
Remove the bolt.
Disengage the 2 clips and guide remove the rear window side garnish LH.
62461A
24.REMOVE REAR WINDOW SIDE GARNISH RH
Use the same procedure described for the LH side.
62639
25.REMOVE REAR QUARTER TRIM GARNISH FRONT LH
Remove the 2 bolts.
Disengage the clip and claw remove the rear quarter trim front garnish LH.
62638
26.REMOVE REAR QUARTER TRIM FRONT GARNISH RH
Use the same procedure described for the LH side.
62412
27.REMOVE CENTER PILLAR GARNISH LH
Remove the 2 bolts and clip.
Disengage the clips and 2 guides to remove the center pillar garnish LH.
62411
28.REMOVE CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
81260A
29.REMOVE MAP LIGHT ASSEMBLY
74320
30.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws.
Disconnect the connector and remove the visor assembly LH (w/ Illumination).
74310
31.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348
32.REMOVE VISOR HOLDER
Disengage the 2 claws remove the 2 visor holders.
63310
33.REMOVE ROOF HEADLINING ASSEMBLY
Disengage the 3 clamps and disconnect the connector from the front pillar RH.
Disengage the 2 clamps and disconnect the connector from the front pillar LH.
Remove the 3 clips at the rear of the roof headlining.
Disconnect the antenna cord sub-assembly connector.
Disengage the clip at the front of the roof headlining, and remove the roof headlining assembly.
Remove the roof headlining assembly from the vehicle through the front passenger side door.
Do not damage the roof headlining assembly or body interior.