Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297766 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the engine is running or the ignition switch is ON, the power window regulator motor assembly is operated by the power window regulator master switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions.

WIRING DIAGRAM

B311524E05
0.896,1.167 1.656,1.365 0.76,0.198 10 false from Battery 2.906,1.333 3.708,1.625 0.802,0.292 10 false D FL DOOR 4.656,2.417 4.99,2.698 0.333,0.281 10 false 6 4.667,3.031 4.99,3.354 0.323,0.323 10 false 7 2.625,2.396 2.938,2.708 0.313,0.313 10 false 1 2.625,3 2.938,3.344 0.313,0.344 10 false 3 4.583,1.083 4.927,1.417 0.344,0.333 10 false 12 4.563,4.604 4.823,4.792 0.26,0.188 10 false E8 1.271,3.656 2.833,4.094 1.563,0.438 10 false Power Window Regulator Motor Assembly 1.281,3.479 1.521,3.656 0.24,0.177 10 false E5 4.656,3.583 5.031,3.938 0.375,0.354 10 false 5 4.563,4.771 6.104,5.25 1.542,0.479 10 false Power Window Regulator Master Switch Assembly 4.833,1.167 5.146,1.49 0.313,0.323 10 false +B 4.833,2.5 5.229,2.802 0.396,0.302 10 false WU 4.833,3.125 5.26,3.469 0.427,0.344 10 false WD 2.313,2.5 2.719,2.823 0.406,0.323 10 false WU 2.323,3.104 2.76,3.448 0.438,0.344 10 false WD 4.833,3.677 5.333,4.042 0.5,0.365 10 false GND 0.219,0.198 0.979,0.396 0.76,0.198 12 false for LHD:

B311524E06
4.583,4.75 6.271,5.646 1.688,0.896 10 false Power Window Regulator Master Switch Assembly 4.583,4.594 4.948,4.792 0.365,0.198 10 false F6 4.667,3.552 4.833,3.75 0.167,0.198 10 false 5 4.667,3 4.833,3.198 0.167,0.198 10 false 7 4.667,2.396 4.833,2.594 0.167,0.198 10 false 6 2.635,2.385 2.802,2.583 0.167,0.198 10 false 1 2.635,3 2.802,3.198 0.167,0.198 10 false 3 4.594,1.063 4.833,1.26 0.24,0.198 10 false 12 4.844,2.51 5.188,2.74 0.344,0.229 10 false WU 4.844,1.177 5.188,1.406 0.344,0.229 10 false +B 4.844,3.104 5.188,3.333 0.344,0.229 10 false WD 2.313,2.521 2.656,2.75 0.344,0.229 10 false WU 2.313,3.115 2.656,3.344 0.344,0.229 10 false WD 4.844,3.677 5.25,3.906 0.406,0.229 10 false GND 1.229,3.635 2.906,4.531 1.677,0.896 10 false Power Window Regulator Motor Assembly RH 1.24,3.438 1.625,3.667 0.385,0.229 10 false F1 2.865,1.344 3.885,1.667 1.021,0.323 10 false D FR DOOR 0.917,1.167 1.938,1.49 1.021,0.323 10 false from Battery 0.219,0.167 1.083,0.646 0.865,0.479 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master Switch / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Master Switch
Tester Display Test Part Control Range Diagnostic Note
Power Window Driver side power window OFF / UP / DOWN -

OK:

Driver door power window operates normally.


CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.



Result
Result Proceed to
NG A
OK B


A

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the E8*1 or F6*2 power window regulator master assembly connector.


b.
U190286E02
1.771,1.438 1.771,1.719 true 2.302,1.229 2.646,1.76 true 0.188,0.156 0.375,0.313 0.188,0.156 10 false *a 1.271,0.646 1.563,0.802 0.292,0.156 10 false E8 1.688,1.76 1.979,1.917 0.292,0.156 10 false +B 2.542,1.792 3.042,1.948 0.5,0.156 10 false GND 1.917,0.646 2.208,0.802 0.292,0.156 10 false F6 1.219,0.323 1.542,0.531 0.323,0.208 12 false *A 1.885,0.323 2.208,0.531 0.323,0.208 12 false *B

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E8-12 (+B)*1 - Body ground Always 11 to 14 V
F6-12 (+B)*2 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
E8-5 (GND)*1 - Body ground Always Below 1 Ω
F6-5 (GND)*2 - Body ground Always Below 1 Ω


*1: for LHD

*2: for RHD



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.


b.

Disconnect the E5*1 or F1*2 power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E8-6 (WU) - E5-1 (WU)*1 Always Below 1 Ω
E8-7 (WD) - E5-3 (WD)*1 Always Below 1 Ω
F6-6 (WU) - F1-1 (WU)*2 Always Below 1 Ω
F6-7 (WD) - F1-3 (WD)*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E8-6 (WU)*1 - Body ground Always Below 1 Ω
E8-7 (WD)*1 - Body ground Always Below 1 Ω
F6-6 (WU)*2 - Body ground Always Below 1 Ω
F6-7 (WD)*2 - Body ground Always Below 1 Ω


*1: for LHD

*2: for RHD




OK

4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver side door power window operates normally.



Result
Result Proceed to
Operate A
Does not operate B


A

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY