When the ignition switch is ON, the power window regulator motor assembly (for front passenger side) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger side) has motor, regulator and ECU functions.
When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Master Switch / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Front passenger side power window | OFF / UP / DOWN | - |
Front passenger side door power window operates normally.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-12 (+B)*1 - Body ground | Always | 11 to 14 V |
| E8-12 (+B)*2 - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-5 (GND)*1 - Body ground | Always | Below 1 Ω |
| E8-5 (GND)*2 - Body ground | Always | Below 1 Ω |
*1: for LHD
*2: for RHD
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Front Power Window Regulator Switch Assembly) |
OK
NG
Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.
Disconnect the F1*1 or E5*2 power window regulator motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-6 (WU) - F1-1 (WU)*1 | Always | Below 1 Ω |
| F6-7 (WD) - F1-3 (WD)*1 | Always | Below 1 Ω |
| E8-6 (WU) - E5-1 (WU)*2 | Always | Below 1 Ω |
| E8-7 (WD) - E5-3 (WD)*2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-6 (WU)*1 - Body ground | Always | 10 kΩ or higher |
| F6-7 (WD)*1 - Body ground | Always | 10 kΩ or higher |
| E8-6 (WU)*2 - Body ground | Always | 10 kΩ or higher |
| E8-7 (WD)*2 - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
OK
NG
Temporarily replace the power window regulator switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).
Check the power window regulator switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Front passenger side door power window operates normally.
| Result | Proceed to |
|---|---|
| Operate | A |
| Does not operate | B |
A
B