Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE
RM2090E _59 Vehicle Exterior _060710 WIPER / WASHER _0297789 WASHER NOZZLE G

WIPER / WASHER  WASHER NOZZLE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85035 1.INSPECT WASHER NOZZLE SUB-ASSEMBLY (for RHD)

a.

With the engine running, check the position where the windshield washer fluid hits the windshield.

Standard:

The washer fluid hits the windshield in the areas shown in the illustration.


B310897E01
2.709,0.491 2.883,0.661 0.174,0.171 10 a 4.142,4.451 4.316,4.622 0.174,0.171 10 j 3.122,4.452 3.296,4.623 0.174,0.171 10 i 5.774,3.73 5.948,3.901 0.174,0.171 10 h 1.298,3.793 1.472,3.964 0.174,0.171 10 g 4.419,3.035 4.593,3.206 0.174,0.171 10 f 2.722,3.063 2.896,3.234 0.174,0.171 10 e 6.451,2.366 6.625,2.536 0.174,0.171 10 d 0.751,2.506 0.925,2.677 0.174,0.171 10 c 4.478,0.458 4.652,0.628 0.174,0.171 10 b

Standard Clearance
Area Measurement Area Measurement
a 684 mm (26.929 in.) b 660 mm (25.984 in.)
c 232 mm (9.134 in.) d 247 mm (9.724 in.)
e 250 mm (9.843 in.) f 268 mm (10.551 in.)
g 299 mm (11.772 in.) h 253 mm (9.961 in.)
i 250 mm (9.843 in.) j 300 mm (11.811 in.)

HINT:

If the result is not as specified, adjust the washer nozzle sub-assembly (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE>ADJUSTMENT).



Hide 85035 2.INSPECT WASHER NOZZLE SUB-ASSEMBLY (for LHD)

a.

With the engine running, check the position where the windshield washer fluid hits the windshield.

Standard:

The washer fluid hits the windshield in the areas shown in the illustration.


B314886E01
2.877,0.499 2.991,0.658 0.113,0.159 10 a 4.128,4.414 4.241,4.573 0.113,0.159 10 j 3.15,4.42 3.263,4.578 0.113,0.159 10 i 5.844,3.813 5.957,3.972 0.113,0.159 10 h 1.44,3.687 1.553,3.846 0.113,0.159 10 g 4.443,3.098 4.556,3.257 0.113,0.159 10 f 2.835,3.058 2.949,3.217 0.113,0.159 10 e 6.428,2.532 6.541,2.691 0.113,0.159 10 d 0.782,2.383 0.895,2.542 0.113,0.159 10 c 4.46,0.558 4.573,0.717 0.113,0.159 10 b

Standard Clearance
Area Measurement Area Measurement
a 660 mm (25.984 in.) b 684 mm (26.929 in.)
c 247 mm (9.724 in.) d 232 mm (9.134 in.)
e 268 mm (10.551 in.) f 250 mm (9.843 in.)
g 253 mm (9.961 in.) h 299 mm (11.772 in.)
i 300 mm (11.811 in.) j 250 mm (9.843 in.)

HINT:

If the result is not as specified, adjust the washer nozzle sub-assembly (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE>ADJUSTMENT).