Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch information signals, and illuminates the front fog light.

WIRING DIAGRAM

E247171E02
3.063,0.49 3.406,0.729 0.344,0.24 10 false 3C 3.104,0.313 3.302,0.531 0.198,0.219 10 false 3 3.104,0.75 3.344,1 0.24,0.25 10 false 5 3.104,1.521 3.25,1.719 0.146,0.198 10 false 1 5.729,3.323 5.906,3.531 0.177,0.208 10 false 7 5.667,1.927 5.917,2.115 0.25,0.188 10 false 30 5.906,2.021 6.365,2.25 0.458,0.229 10 false FFGO 5.906,3.406 6.354,3.646 0.448,0.24 10 false TRLY 3.99,0.646 4.792,0.885 0.802,0.24 10 false FR FOG LH 0.521,0.49 2.323,0.802 1.802,0.313 10 false Fog Light Assembly LH 0.521,0.958 2.323,1.271 1.802,0.313 10 false Fog Light Assembly RH 3.729,4.052 5.583,4.719 1.854,0.667 10 false Instrument Panel Junction Block Assembly 5.469,5.01 7.073,5.406 1.604,0.396 10 false Main Body ECU (Network Gateway ECU) 3.99,1.125 4.802,1.333 0.813,0.208 10 false FR FOG RH 0.448,1.708 1.281,1.938 0.833,0.229 10 false from Battery 3.063,0.948 3.365,1.219 0.302,0.271 10 false 3C 3.063,1.719 3.354,1.917 0.292,0.198 10 false 3E 5.469,4.854 5.771,5.042 0.302,0.188 10 false MB 4.781,2.823 5.198,3.01 0.417,0.188 10 false TAIL 4.115,3.719 4.531,3.948 0.417,0.229 10 false TAIL 4.042,2.302 4.708,2.479 0.667,0.177 10 false FR FOG

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FR FOG RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Front Fog Light Relay Front fog light relay ON/OFF Light control switch is in TAIL position

OK:

Front fog light relay operates (front fog lights come on).


Result :
Result Proceed to
NG A
OK B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.


U190422E02
2.573,2.052 2.573,2.281 true 4.969,2.042 4.969,2.271 true 0.198,0.073 0.385,0.229 0.188,0.156 10 false *a 1.76,0.208 2.052,0.365 0.292,0.156 10 false 3C 5.188,0.188 5.479,0.344 0.292,0.156 10 false 3E 3.469,1.5 3.76,1.656 0.292,0.156 10 false MB 2.406,2.344 2.896,2.583 0.49,0.24 10 false TRLY 4.813,2.323 5.302,2.563 0.49,0.24 10 false FFGO

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Voltage:
Tester Connection Condition Specified Condition
MB-30 (FFGO) - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V
3C-3 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY), MB-30 (FFGO)
11 to 14 V
3C-5 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY), MB-30 (FFGO)
11 to 14 V



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY