Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch assembly information signals, and illuminates the clearance lights, taillights and license plate lights.

WIRING DIAGRAM

E247169E02
2.781,0.333 2.958,0.542 0.177,0.208 10 false 1 5.583,0.469 5.792,0.677 0.208,0.208 10 false 7 5.75,0.542 6.25,0.802 0.5,0.26 10 false TRLY 3.063,3.115 4.844,3.458 1.781,0.344 10 false Instrument Panel Junction Block Assembly 5.323,4.01 6.948,4.385 1.625,0.375 10 false Main Body ECU (Network Gateway ECU) 0.802,0.51 1.583,0.708 0.781,0.198 10 false from Battery 0.354,1.344 1.635,1.552 1.281,0.208 10 false License Plate Lights 1.042,2.042 1.604,2.229 0.563,0.188 10 false Taillights 0.448,2.417 1.646,2.604 1.198,0.188 10 false Clearance Light LH 0.438,2.844 1.646,3.031 1.208,0.188 10 false Clearance Light RH 2.75,0.552 3.01,0.771 0.26,0.219 10 false 3E 5.354,3.833 5.677,4.042 0.323,0.208 10 false MB 2.74,1.188 3.01,1.406 0.271,0.219 10 false 24 3.896,1.521 4.344,1.76 0.448,0.24 10 false TAIL 2.74,1.375 3,1.542 0.26,0.167 10 false 3D 2.74,2.229 3.042,2.458 0.302,0.229 10 false 12 2.74,2.438 3.031,2.656 0.292,0.219 10 false 3C 2.74,2.677 3.052,2.927 0.313,0.25 10 false 13 2.74,2.854 3.01,3.052 0.271,0.198 10 false 3C 3.906,1.083 4.281,1.281 0.375,0.198 10 false TAIL

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TAIL RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -

OK:

Taillight relay operates (taillights illuminate).


Result:
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK)

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the 3E instrument panel junction block assembly connector.


b.
U190433E02
0.167,0.042 0.354,0.198 0.188,0.156 10 false *a 1.656,0.469 1.948,0.625 0.292,0.156 10 false 3E

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

U147263E03
4.219,2.135 4.219,2.365 true 0.229,0.104 0.417,0.26 0.188,0.156 10 false *a 1.698,0.771 1.896,0.927 0.198,0.156 10 false 3D 5.167,0.292 5.406,0.458 0.24,0.167 10 false 3E 5.094,1.594 5.385,1.75 0.292,0.156 10 false MB 4.094,2.406 4.469,2.583 0.375,0.177 10 false TRLY

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3C-12 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V
3C-13 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V
3D-24 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - 3C-12 Always 10 kΩ or higher
3E-1 - 3C-13 Always 10 kΩ or higher
3E-1 - 3D-24 Always 10 kΩ or higher



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY