Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.06
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Turn Signal Switch Circuit  


DESCRIPTION

The turn signal flasher assembly receives the main body ECU (network gateway ECU) information and controls the turn signal lights.

WIRING DIAGRAM

w/ Side Turn Signal Light



E351705E02
1.167,0.708 1.479,0.906 0.313,0.198 10 false D5 1.177,0.51 1.49,0.708 0.313,0.198 10 false 17 1.167,1.208 1.479,1.406 0.313,0.198 10 false D6 1.208,1 1.521,1.198 0.313,0.198 10 false 9 3.635,1.26 3.948,1.458 0.313,0.198 10 false 13*1 3.635,1.656 3.948,1.854 0.313,0.198 10 false TR 4.271,1.656 4.583,1.854 0.313,0.198 10 false TL 3.479,2.052 3.792,2.25 0.313,0.198 10 false TR 4.135,2.052 4.448,2.25 0.313,0.198 10 false TL 3.813,2.052 4.125,2.25 0.313,0.198 10 false EL 4.479,2.25 4.792,2.448 0.313,0.198 10 false LH 4.521,2.448 4.833,2.646 0.313,0.198 10 false N 4.469,2.646 4.781,2.844 0.313,0.198 10 false RH 4.885,2.344 6.396,2.615 1.51,0.271 10 false Turn Signal Switch 3.958,2.844 4.271,3.042 0.313,0.198 10 false EL 4.448,3.104 4.76,3.302 0.313,0.198 10 false D50 4.458,3.271 6.875,3.5 2.417,0.229 10 false Headlight Dimmer Switch Assembly 4.01,3.125 4.323,3.323 0.313,0.198 10 false 12*1 5.958,4.104 6.271,4.302 0.313,0.198 10 false EL 5.958,4.625 6.271,4.823 0.313,0.198 10 false ER 5.698,3.969 6.01,4.167 0.313,0.198 10 false 5 5.708,4.49 6.021,4.688 0.313,0.198 10 false 6 2.521,4.604 2.833,4.802 0.313,0.198 10 false 3C 2.531,4.396 2.844,4.594 0.313,0.198 10 false 27 2.51,4.094 2.823,4.292 0.313,0.198 10 false 3B 2.521,3.896 2.833,4.094 0.313,0.198 10 false 23 1.167,3.875 1.479,4.073 0.313,0.198 10 false 24 1.167,4.396 1.479,4.594 0.313,0.198 10 false 25 1.135,4.094 1.448,4.292 0.313,0.198 10 false MB 1.146,4.604 1.458,4.802 0.313,0.198 10 false MB 5.635,5.906 5.948,6.104 0.313,0.198 10 false D61 5.625,6.156 7.031,6.563 1.406,0.406 10 false Turn Signal Flasher Assembly 0.313,5.167 2.042,5.781 1.729,0.615 10 false Main Body ECU (Network Gateway ECU) 0.208,6.073 2.917,6.271 2.708,0.198 10 false Instrument Panel Junction Block Assembly 0.615,0.719 1.115,0.938 0.5,0.219 10 false TSWL 0.594,1.219 0.99,1.417 0.396,0.198 10 false TSWR 0.573,4.104 1.135,4.438 0.563,0.333 10 false TURNL 0.552,4.625 1.115,4.958 0.563,0.333 10 false TURNR 3.635,1.417 3.948,1.615 0.313,0.198 10 false 16*2 4.271,1.417 4.583,1.615 0.313,0.198 10 false 18*2 4.271,1.26 4.583,1.458 0.313,0.198 10 false 15*1 4.01,3.302 4.323,3.5 0.313,0.198 10 false 19*2 3.688,6.073 4.563,6.271 0.875,0.198 10 false *1: for LHD 3.688,6.292 4.563,6.49 0.875,0.198 10 false *2: for LHD

E351704E04
2.875,0.646 3.188,0.844 0.313,0.198 10 false 3C 4.24,0.646 4.552,0.844 0.313,0.198 10 false 3A 4.24,3.583 4.552,3.781 0.313,0.198 10 false 3A 2.875,2.615 3.188,2.813 0.313,0.198 10 false 3D 2.875,1.635 3.188,1.833 0.313,0.198 10 false 3C 2.875,3.583 3.188,3.781 0.313,0.198 10 false 3C 2.885,4.542 3.198,4.74 0.313,0.198 10 false 3C 2.885,5.469 3.198,5.667 0.313,0.198 10 false 3D 2.896,1.438 3.208,1.635 0.313,0.198 10 false 31 4.292,0.427 4.604,0.625 0.313,0.198 10 false 6 5.677,3.469 5.99,3.667 0.313,0.198 10 false 2 5.885,3.573 6.198,3.771 0.313,0.198 10 false LR 5.927,0.635 6.24,0.833 0.313,0.198 10 false LL 5.698,0.531 6.01,0.729 0.313,0.198 10 false 3 5.198,5.865 5.51,6.063 0.313,0.198 10 false D61 5.198,6.042 7.146,6.24 1.948,0.198 10 false Turn Signal Flasher Assembly 3.125,5.948 4.906,6.396 1.781,0.448 10 false Instrument Panel Junction Block Assembly 4.281,3.365 4.594,3.563 0.313,0.198 10 false 4 2.885,0.448 3.198,0.646 0.313,0.198 10 false 16 2.885,2.406 3.198,2.604 0.313,0.198 10 false 18 1.875,1.51 2.188,1.708 0.313,0.198 10 false 1 0.688,1.5 1,1.698 0.313,0.198 10 false 2 1.667,5.479 1.979,5.677 0.313,0.198 10 false B 0.896,5.469 1.208,5.667 0.313,0.198 10 false E 1.854,4.417 2.167,4.615 0.313,0.198 10 false 1 0.688,4.427 1,4.625 0.313,0.198 10 false 2 1.635,4.542 1.948,4.74 0.313,0.198 10 false B 0.885,4.542 1.198,4.74 0.313,0.198 10 false E 0.688,3.458 1,3.656 0.313,0.198 10 false 4 1.885,3.448 2.198,3.646 0.313,0.198 10 false 1 0.521,1.781 0.833,1.979 0.313,0.198 10 false A3 0.531,1.958 2.74,2.365 2.208,0.406 10 false Side Turn Signal Light Assembly LH 0.552,4.917 2.76,5.323 2.208,0.406 10 false Side Turn Signal Light Assembly RH 0.563,1 2.135,1.219 1.573,0.219 10 false Headlight Assembly LH 0.552,0.844 0.865,1.01 0.313,0.167 10 false A60 0.677,0.51 0.875,0.698 0.198,0.188 10 false 4 1.896,0.51 4.104,0.917 2.208,0.406 10 false 1 0.573,3.01 3.01,3.188 2.438,0.177 10 false Rear Combination Light Assembly LH 0.542,3.948 2.698,4.146 2.156,0.198 10 false Headlight Assembly RH 0.521,3.76 2.729,4.167 2.208,0.406 10 false A38 0.552,4.75 0.865,4.948 0.313,0.198 10 false A44 0.51,5.896 2.938,6.177 2.427,0.281 10 false Rear Combination Light Assembly RH 0.698,2.469 1.01,2.667 0.313,0.198 10 false 2 1.854,2.49 2.167,2.688 0.313,0.198 10 false 1 0.885,1.615 1.198,1.813 0.313,0.198 10 false E 1.646,1.625 1.958,1.823 0.313,0.198 10 false B 0.698,5.344 1.01,5.542 0.313,0.198 10 false 2 1.885,5.344 2.198,5.542 0.313,0.198 10 false 1 0.583,2.844 2.792,3.25 2.208,0.406 10 false H6 0.531,5.729 2.74,6.135 2.208,0.406 10 false H1 2.885,4.323 3.198,4.521 0.313,0.198 10 false 32 2.917,5.26 3.229,5.458 0.313,0.198 10 false 1 2.885,3.365 3.198,3.563 0.313,0.198 10 false 20 1.667,2.604 1.979,2.802 0.313,0.198 10 false B 0.885,2.604 1.198,2.802 0.313,0.198 10 false E

w/o Side Turn Signal Light



E351707E04
0.979,2 2.552,2.396 1.573,0.396 10 false Main body ECU (Network Gateway ECU) 2.063,0.604 2.375,0.802 0.313,0.198 10 false 17 2.104,1.094 2.417,1.292 0.313,0.198 10 false 9 5.865,0.698 6.177,0.896 0.313,0.198 10 false 5 5.854,1.188 6.167,1.385 0.313,0.198 10 false 6 6.167,0.823 6.479,1.021 0.313,0.198 10 false EL 6.167,1.333 6.479,1.531 0.313,0.198 10 false ER 3.958,3.563 4.271,3.76 0.313,0.198 10 false TL 4.573,3.552 4.885,3.75 0.313,0.198 10 false TR 4.271,3.552 4.583,3.75 0.313,0.198 10 false EL 3.573,3.76 3.885,3.958 0.313,0.198 10 false LH 3.615,3.958 3.927,4.156 0.313,0.198 10 false N 3.563,4.146 3.875,4.344 0.313,0.198 10 false RH 1.885,3.854 3.469,4.219 1.583,0.365 10 false Turn Signal Switch 1.583,4.792 4.042,5.25 2.458,0.458 10 false Headlight Dimmer Switch Assembly 1.594,4.625 3.177,4.99 1.583,0.365 10 false D50 4.073,2.75 4.385,2.948 0.313,0.198 10 false 15*1 4.698,2.927 5.01,3.125 0.313,0.198 10 false 16*2 4.688,3.167 5,3.365 0.313,0.198 10 false TR 4.438,4.385 4.75,4.583 0.313,0.198 10 false EL 4.438,4.781 4.75,4.979 0.313,0.198 10 false 19*2 4.104,3.156 4.417,3.354 0.313,0.198 10 false TL 6.104,6.01 6.417,6.208 0.313,0.198 10 false LL 5.844,5.833 6.156,6.031 0.313,0.198 10 false 3 4.5,5.75 4.813,5.948 0.313,0.198 10 false 6 4.469,5.99 4.781,6.188 0.313,0.198 10 false 3A 3.104,5.99 3.417,6.188 0.313,0.198 10 false 3C 3.104,7.271 3.417,7.469 0.313,0.198 10 false 3D 3.094,5.75 3.406,5.948 0.313,0.198 10 false 16 3.094,7.052 3.406,7.25 0.313,0.198 10 false 18 0.865,6.313 1.177,6.51 0.313,0.198 10 false A60 0.76,7.552 1.073,7.75 0.313,0.198 10 false H6 5.719,8.094 6.969,8.573 1.25,0.479 10 false Turn Signal Flasher Assembly 5.708,7.938 7.156,8.417 1.448,0.479 10 false D61 3.146,7.969 4.75,8.51 1.604,0.542 10 false Instrument Panel Junction Block Assembly 0.844,6.479 2.49,6.781 1.646,0.302 10 false Headlight Assembly LH 0.729,7.74 3.021,8.073 2.292,0.333 10 false Rear Combination Light Assembly LH 0.906,5.865 1.219,6.063 0.313,0.198 10 false 6 2.073,5.865 2.385,6.063 0.313,0.198 10 false 3 2.063,7.167 2.375,7.365 0.313,0.198 10 false 4 0.906,7.177 1.219,7.375 0.313,0.198 10 false 2 1.875,7.281 2.188,7.479 0.313,0.198 10 false B 1.135,7.281 1.448,7.479 0.313,0.198 10 false E 2.073,0.823 2.385,1.021 0.313,0.198 10 false D5 2.063,1.323 2.375,1.521 0.313,0.198 10 false D6 1.521,0.833 2.198,1.167 0.677,0.333 10 false TSWL 1.51,1.323 2.188,1.656 0.677,0.333 10 false TSWR 4.073,2.917 4.385,3.115 0.313,0.198 10 false 18*2 4.698,2.76 5.01,2.958 0.313,0.198 10 false 13*1 4.427,4.635 4.74,4.833 0.313,0.198 10 false 12*1 0.26,8.188 1.031,8.385 0.771,0.198 10 false *1: for LHD 0.25,8.469 1.021,8.667 0.771,0.198 10 false *2: for RHD

E351708E04
5.75,1.938 6.208,2.135 0.458,0.198 10 false D61 5.74,2.104 7.031,2.542 1.292,0.438 10 false Turn Signal Flasher Assembly 3.135,2.021 4.76,2.479 1.625,0.458 10 false Instrument Panel Junction Block Assembly 5.927,0.5 6.385,0.698 0.458,0.198 10 false LR 4.313,0.281 4.771,0.479 0.458,0.198 10 false 4 2.896,0.49 3.354,0.688 0.458,0.198 10 false 3C 2.896,1.573 3.354,1.771 0.458,0.198 10 false 3D 2.906,0.281 3.365,0.479 0.458,0.198 10 false 20 2.938,1.375 3.396,1.573 0.458,0.198 10 false 1 0.573,0.729 1.031,0.927 0.458,0.198 10 false A38 0.521,1.802 0.979,2 0.458,0.198 10 false H1 5.698,0.354 6.177,0.771 0.479,0.417 10 false 2 4.26,0.49 4.719,0.688 0.458,0.198 10 false 3A 0.563,0.885 2.104,1.281 1.542,0.396 10 false Headlight Assembly RH 0.5,1.958 2.844,2.354 2.344,0.396 10 false Rear Combination Light Assembly RH 1.865,1.479 2.323,1.677 0.458,0.198 10 false 4 0.719,1.469 1.177,1.667 0.458,0.198 10 false 2 0.917,1.573 1.375,1.771 0.458,0.198 10 false E 1.667,1.583 2.125,1.781 0.458,0.198 10 false B 0.729,0.365 1.188,0.563 0.458,0.198 10 false 4 1.865,0.375 2.323,0.573 0.458,0.198 10 false 3

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result:
Result Proceed to
w/ side turn signal light A
w/o side turn signal light B




A

2.READ VALUE USING GTS (TURN SIGNAL SWITCH)

B

9.READ VALUE USING GTS (TURN SIGNAL SWITCH)
2.READ VALUE USING GTS (TURN SIGNAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Left Turn Signal Switch Left turn signal switch signal ON or OFF ON: Left turn signal switch on
OFF: Left turn signal switch off
-
Right Turn Signal Switch Right turn signal switch signal ON or OFF ON: Right turn signal switch on
OFF: Right turn signal switch off
-

OK:

Normal conditions listed above are displayed.




OK

3.READ VALUE USING GTS (TURN SIGNAL LIGHT)

NG

7.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
3.READ VALUE USING GTS (TURN SIGNAL LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Left Turn Signal Light Left turn signal light output ON or OFF ON: Left turn signal switch on
OFF: Left turn signal switch off
-
Right Turn Signal Light Right turn signal light output ON or OFF ON: Right turn signal switch on
OFF: Right turn signal switch off
-

OK:

Normal conditions listed above are displayed.




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
4.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the 3B and 3C main body ECU (network gateway ECU) connectors.


b.

Disconnect the D61 turn signal flasher assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-23 - D61-5 Always Below 1 Ω
3C-27 - D61-6 Always Below 1 Ω
3B-23 or D61-5 - Body ground Always 10 kΩ or higher
3C-27 or D61-6 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the 3A main body ECU (network gateway ECU) connectors.


b.

Disconnect the D61 turn signal flasher assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - D61-2 (LR) Always Below 1 Ω
3A-6 - D61-3 (LL) Always Below 1 Ω
3A-4 or D61-2 (LR) - Body ground Always 10 kΩ or higher
3A-6 or D61-3 (LL) - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Disconnect the 3A, 3C and 3D instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3C-20 Always Below 1 Ω
3A-4 - 3C-32 Always Below 1 Ω
3A-4 - 3D-1 Always Below 1 Ω
3A-6 - 3C-16 Always Below 1 Ω
3A-6 - 3C-31 Always Below 1 Ω
3A-6 - 3D-18 Always Below 1 Ω




OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
a.

Remove the headlight dimmer switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL).


b.

Inspect the headlight dimmer switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - HEADLIGHT DIMMER SWITCH ASSEMBLY)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - HEADLIGHT DIMMER SWITCH ASSEMBLY)
a.

Disconnect the D5 and D6 main body ECU (network gateway ECU) connectors.


b.

Disconnect the D50 headlight dimmer switch assembly connectors.


c.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-17 - D50-15(TL) Always Below 1 Ω
D6-9 - D50-13(TR) Always Below 1 Ω
D50-12(EL) - Body ground Always Below 1 Ω
D5-17 or D50-15(TL) - Body ground Always 10 kΩ or higher
D6-9 or D50-13(TR) - Body ground Always 10 kΩ or higher




d.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-17 - D50-18(TL) Always Below 1 Ω
D6-9 - D50-16(TR) Always Below 1 Ω
D50-19(EL) - Body ground Always Below 1 Ω
D5-17 or D50-18(TL) - Body ground Always 10 kΩ or higher
D6-9 or D50-16(TR) - Body ground Always 10 kΩ or higher





OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

9.READ VALUE USING GTS (TURN SIGNAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Left Turn Signal Switch Left turn signal switch signal ON or OFF ON: Left turn signal switch on
OFF: Left turn signal switch off
-
Right Turn Signal Switch Right turn signal switch signal ON or OFF ON: Right turn signal switch on
OFF: Right turn signal switch off
-

OK:

Normal conditions listed above are displayed.




OK

10.READ VALUE USING GTS (TURN SIGNAL LIGHT)

NG

13.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
10.READ VALUE USING GTS (TURN SIGNAL LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Left Turn Signal Light Left turn signal light output ON or OFF ON: Left turn signal switch on
OFF: Left turn signal switch off
-
Right Turn Signal Light Right turn signal light output ON or OFF ON: Right turn signal switch on
OFF: Right turn signal switch off
-

OK:

Normal conditions listed above are displayed.




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

11.INSPECT HEADLIGHT DIMMER SWITCH
11.INSPECT HEADLIGHT DIMMER SWITCH
a.

Remove the headlight dimmer switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL).


b.

Inspect the headlight dimmer switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION).



OK

12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - HEADLIGHT DIMMER SWITCH ASSEMBLY)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - HEADLIGHT DIMMER SWITCH ASSEMBLY)
a.

Disconnect the D61 turn signal flasher assembly connectors.


b.

Disconnect the D50 headlight dimmer switch assembly connectors.


c.

for LHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-15(TL) - D61-5(EL) Always Below 1 Ω
D50-13(TR) - D61-6(ER) Always Below 1 Ω
D50-12(EL) - Body ground Always Below 1 Ω
D50-15(TL) or D61-5(EL) - Body ground Always 10 kΩ or higher
D50-13(TR) or D61-6(ER) - Body ground Always 10 kΩ or higher




d.

for RHD:

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-18(TL) - D61-5(EL) Always Below 1 Ω
D50-16(TR) - D61-6(ER) Always Below 1 Ω
D50-19(EL) - Body ground Always Below 1 Ω
D50-18(TL) or D61-5(EL) - Body ground Always 10 kΩ or higher
D50-16(TR) or D61-6(ER) - Body ground Always 10 kΩ or higher





OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connectors.


b.

Disconnect the D61 turn signal flasher assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - D61-2 (LR) Always Below 1 Ω
3A-6 - D61-3 (LL) Always Below 1 Ω
3A-4 or D61-2 (LR) - Body ground Always 10 kΩ or higher
3A-6 or D61-3 (LL) - Body ground Always 10 kΩ or higher




OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Disconnect the 3A, 3C and 3D instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3C-20 Always Below 1 Ω
3A-4 - 3D-1 Always Below 1 Ω
3A-6 - 3C-16 Always Below 1 Ω
3A-4 - 3D-18 Always Below 1 Ω




OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY