Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297682 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) Y

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the engine immobiliser system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

HINT:

A simple method to determine whether the battery is depleted is to operate the horn.


Result:
Proceed to
NEXT



NEXT

3.TURN ENGINE SWITCH ON (IG)
3.TURN ENGINE SWITCH ON (IG)
HINT:

If the engine switch cannot be turned on (IG), communication with the GTS can be confirmed by connecting the GTS to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
LIN DTC is not output A
LIN DTC is output B



A

6.CHECK FOR DTC (ENTRY AND START SYSTEM)*

B

6.CHECK FOR DTC (ENTRY AND START SYSTEM)*
a.

Check for DTCs and make a note of any codes that are output.



c.

Recheck for DTCs. Based on the DTCs output above, try to duplicate the engine immobiliser system DTC or steering lock system DTC by simulating the symptoms indicated by the DTCs.


Result:
Result Proceed to
DTC is not output A
Steering lock system DTC is output (DTC B2781, B2782 or B2788) B
Engine immobiliser system DTC is output (except DTC B2781, B2782 and B2788) C



A

7.CHECK FOR DTC (SFI SYSTEM)*

B

C

7.CHECK FOR DTC (SFI SYSTEM)*

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

HINT:

The DTCs for the engine immobiliser system are specified above. If other codes are output, check the DTC chart for the SFI system.



Result:
Result Proceed to
DTC is not output A
Engine immobiliser system DTC is output (DTC B2799, B279A or B279C) B
SFI system DTC is output) C



A

8.PROBLEM SYMPTOMS TABLE

B

C

8.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

10.ADJUST, REPAIR OR REPLACE
9.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

10.ADJUST, REPAIR OR REPLACE
10.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC*
11.CHECK FOR DTC*


Result:
Result Proceed to
DTC is not output A
Engine immobiliser system DTC is output B



A

END

B