Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for Floating Type Caliper) › from 2016.06
RM2090E _54 Brake _060686 BRAKE (FRONT) _0297633 FRONT BRAKE(for Floating Type Caliper) A

BRAKE (FRONT)  FRONT BRAKE(for Floating Type Caliper)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RH and LH sides.

·

The procedure listed below is for LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.

When reusing the disc

i.

Align the matchmarks placed when removing, and install the front disc to the axle hub.



b.

When replacing the front disc

i.

Install a new front disc to the axle hub and measure the disc runout (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>ON-VEHICLE INSPECTION).



c.

Temporarily tighten the hub nut and fix the front disc to the axle hub.


Hide 2.INSTALL CARRIER

a.
C257510

Install the carrier with new 2 bolts.

Torque:
Bolt Type A : 80 N*m (816 kgf*cm, 59 ft.*lbf)
Bolt Type B : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Check that there is no dirt, foreign matter or rust on the carrier and clean if necessary.


HINT:
C398290C03
0.219,0.135 0.531,0.333 0.313,0.198 10 false *A 0.208,1.365 0.521,1.563 0.313,0.198 10 false *B 0.813,0.448 1.125,0.646 0.313,0.198 10 false *a 0.802,1.552 1.115,1.75 0.313,0.198 10 false *a
*A Bolt Type A
*B Bolt Type B
*a Width Across Flats


Bolt type A and bolt type B can be distinguished by the sizes of the mounting bolts.

Bolt Type Width Across Flats
A 17 mm (0.669 in.)
B 19 mm (0.748 in.)



Hide 47769 3.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C261019C02
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the inner face of the 2 new front disc brake cylinder slide bushes as shown in the illustration.


Hide 4.INSTALL BUSH

a.
C261020C02
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin with a new bush.


b.

Install the bush to the No. 2 front disc brake cylinder slide pin.


Hide 47715D 5.INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C261021C02
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of the No. 2 front disc brake cylinder slide pin, as shown in the illustration.


b.

Install the No. 2 front disc brake cylinder slide pin to the carrier.


Hide 47715A 6.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C261022C02
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of the front disc brake cylinder slide pin, as shown in the illustration.


b.

Install the front disc brake cylinder slide pin to the carrier.


Hide 47716 7.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE (LOWER)

a.
C256672C02
0,0 0,0 false
V100144

MP Grease


Apply a light layer of MP grease to contact section of the carrier with the front disc brake pad support plate (lower).


b.
C256671C03
0,0 0,0 false
V100144

MP Grease


Apply a light layer of MP grease to the front disc brake pad support plate (lower) as shown in the illustration.


c.

Install the front disc brake pad support plate (lower) to the carrier.


Hide 47717 8.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE (UPPER)

HINT:

Use the same procedure as for the front disc brake pad support plate (lower).


Hide 9.INSTALL FRONT DISC BRAKE PAD

a.

Type A:

i.

Install the cover (shim) to each front disc brake pad.

C417270C06
1.917,2 1.917,2.469 1.917,2.469 2.083,2.469 false 0.969,1.594 0.969,2.063 0.969,2.063 1.135,2.063 false 5.333,1.031 5.333,0.583 5.333,0.583 5.5,0.583 false 6.333,1.438 6.333,0.99 6.333,0.99 6.5,0.99 false 1.208,1.979 1.521,2.177 0.313,0.198 10 false *1 6.563,0.917 6.875,1.115 0.313,0.198 10 false *1 5.552,0.51 5.865,0.708 0.313,0.198 10 false *2 2.146,2.396 2.458,2.594 0.313,0.198 10 false *2
*1 Cover (shim) *2 Front Disc Brake Pad



ii.

Install the front disc brake pads to the carrier.



b.

Type B:

i.

Install the front disc brake pads to the carrier.

C270502C04
6.083,0.625 5.333,0.625 5.333,0.625 5.333,1.031 false 1.063,2.396 1.885,2.396 1.885,2.396 1.885,2 false 6.135,0.563 6.698,0.99 0.563,0.427 10 *1 0.875,2.313 1.25,2.573 0.375,0.26 10 *1
*1 Front Disc Brake Pad - -




Hide 10.INSTALL FRONT DISC BRAKE CYLINDER SUB-ASSEMBLY

a.
C256645

Install the front disc brake cylinder sub-assembly LH to the carrier with the 2 bolts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

NOTICE:

Check that there is no dirt, foreign matter or rust on the front disc brake cylinder sub-assembly LH and clean if necessary.



Hide 47313A 11.CONNECT NO. 1 FRONT FLEXIBLE HOSE

a.

Install the No. 1 front flexible hose to the disc brake cylinder assembly with 2 new gaskets and the new union bolt.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 14.INSPECT FLUID LEAK

Hide 16.INSTALL FRONT WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)