Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2019.03
RM2090E _56 Audio / Visual / Telematics _082076 PARK ASSIST / MONITORING _0396236 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the inner rear view mirror assembly.

WIRING DIAGRAM

E420457E02
5.021,3.271 7.146,3.719 2.125,0.448 10 false Inner Rear View Mirror Assembly 0.188,2.615 2.5,2.979 2.313,0.365 10 false Rear Television Camera Assembly 0.292,3.438 1.375,3.781 1.083,0.344 10 false *: Shielded 2.49,2.26 2.781,2.531 0.292,0.271 10 false * 0.188,2.427 0.479,2.698 0.292,0.271 10 false J5 5.031,3.115 5.323,3.385 0.292,0.271 10 false K6 3.51,2.281 3.802,2.552 0.292,0.271 10 false * 4.531,2.271 4.823,2.542 0.292,0.271 10 false * 1.719,0.563 2.01,0.833 0.292,0.271 10 false 3 1.729,1.01 2.021,1.281 0.292,0.271 10 false 4 1.719,1.469 2.01,1.74 0.292,0.271 10 false 1 1.729,1.958 2.021,2.229 0.292,0.271 10 false 2 5.563,2.344 5.854,2.615 0.292,0.271 10 false 2 5.573,2.75 5.865,3.021 0.292,0.271 10 false 5 5.542,0.573 5.833,0.844 0.292,0.271 10 false 6 5.563,1.031 5.854,1.302 0.292,0.271 10 false 7 5.552,1.51 5.844,1.781 0.292,0.271 10 false 8 5.563,1.958 5.854,2.229 0.292,0.271 10 false 9 1.198,0.698 1.677,0.979 0.479,0.281 10 false CB+ 1.135,1.167 1.615,1.448 0.479,0.281 10 false CGND 1.229,1.635 1.708,1.917 0.479,0.281 10 false CV+ 1.26,2.083 1.74,2.365 0.479,0.281 10 false CV-

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the K6 inner rear view mirror assembly connector.


b.

Disconnect the J5 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K6-6 - J5-3 (CB+) Always Below 1 Ω
K6-7 - J5-4 (CGND) Always Below 1 Ω
K6-8 - J5-1 (CV+) Always Below 1 Ω
K6-9 - J5-2 (CV-) Always Below 1 Ω
K6-6 or J5-3 (CB+) - Body ground Always 10 kΩ or higher
K6-7 or J5-4 (CGND) - Body ground Always 10 kΩ or higher
K6-8 or J5-1 (CV+) - Body ground Always 10 kΩ or higher
K6-9 or J5-2 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK INNER REAR VIEW MIRROR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK INNER REAR VIEW MIRROR ASSEMBLY
a.
E389366C02
1.469,0.167 1.885,0.417 0.417,0.25 0.125,0.167 0.531,0.604 0.406,0.438 10 false *a 1.594,0.219 2.021,0.5 0.427,0.281 10 false K6
*a Component with harness connected
(Inner Rear View Mirror Assembly)


Reconnect the K6 inner rear view mirror assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K6-7 - Body ground Always Below 1 Ω
K6-9 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K6-6 - Body ground Ignition switch ON, shift lever in R 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE INNER REAR VIEW MIRROR ASSEMBLY

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the K6 inner rear view mirror assembly connector.

E389367C02
1.313,0.573 1.729,0.823 0.417,0.25 3.333,2.24 3.49,1.844 true 3.792,2.229 3.594,1.74 true 5.5,2.115 5.656,1.719 true 5.969,2.167 5.771,1.677 true 0.219,0.24 0.646,0.625 0.427,0.385 10 false *a 1.448,0.615 1.917,0.896 0.469,0.281 10 false K6 2.979,0.531 3.406,0.917 0.427,0.385 10 false *b 5.135,0.469 5.563,0.854 0.427,0.385 10 false *c 2.792,1.354 3.344,1.719 0.552,0.365 10 false GND 4.906,1.354 5.458,1.719 0.552,0.365 10 false GND 3.229,2.302 3.656,2.688 0.427,0.385 10 false *d 3.75,2.292 4.177,2.677 0.427,0.385 10 false *e 5.99,2.219 6.417,2.604 0.427,0.385 10 false *e 5.365,2.177 5.792,2.563 0.427,0.385 10 false *d
*a Component with harness connected
(Inner Rear View Mirror Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear view mirror assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) K6-8 - K6-2
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY