Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM J

K3-VE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the coil, which closes the contact point of the EFI MAIN relay, and power is supplied to terminal +B1 of the ECM.

WIRING DIAGRAM

A263068E03
6.385,2.677 6.896,3.052 0.51,0.375 10 ECM 6.229,1.25 6.656,1.552 0.427,0.302 10 +B1 6.229,2.115 6.792,2.521 0.563,0.406 10 E1 5.865,1.26 6.323,1.615 0.458,0.354 10 C23 5.948,1.063 6.208,1.313 0.26,0.25 10 7 5.875,2.125 6.281,2.417 0.406,0.292 10 C24 5.917,1.927 6.396,2.365 0.479,0.438 10 32 0.698,3.625 1.688,4.208 0.99,0.583 10 BATTERY 0.573,2.833 1.51,3.302 0.938,0.469 10 FL MAIN 0.552,1.583 1.219,1.958 0.667,0.375 10 AM2 2.906,1.688 3.75,2.344 0.844,0.656 10 EFI 4.01,1.583 5.49,2.125 1.479,0.542 10 EFI MAIN 2.906,0.979 3.323,1.281 0.417,0.302 10 E/G 1.094,0.75 1.74,1.229 0.646,0.479 10 AM2 1.823,0.75 2.396,1.198 0.573,0.448 10 IG2 0.969,1.208 1.604,1.667 0.635,0.458 10 E28 0.958,1.385 2.531,1.844 1.573,0.458 10 IGNITION SWITCH 0.917,0.75 1.292,1.104 0.375,0.354 10 5 2.135,0.75 2.531,1.115 0.396,0.365 10 6 3.917,0.74 4.229,1.063 0.313,0.323 10 2 4.646,0.74 5.125,1.063 0.479,0.323 10 1 3.917,1.146 4.083,1.385 0.167,0.24 10 3 4.646,1.135 4.979,1.406 0.333,0.271 10 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT ECM (+B1 VOLTAGE)
a.
A141531C18
0.688,1.042 1,1.229 0.313,0.188 1.51,1.042 1.823,1.229 0.313,0.188 0.458,2.396 0.594,1.531 true 1.969,2.406 1.646,1.813 true 0.323,2.438 0.833,2.885 0.51,0.448 10 +B1 1.917,2.438 2.771,2.917 0.854,0.479 10 E1 0.177,0.167 0.625,0.5 0.448,0.333 10 *a 0.719,1.052 1.302,1.563 0.583,0.51 10 C23 1.542,1.052 2.198,1.469 0.656,0.417 10 C24
*a Rear view of wire harness connector
(to ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C23-7 (+B1) - C24-32 (E1) Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the negative battery cable.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-32 (E1) - Body ground Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the negative battery cable.

Result:
Proceed to
OK
NG




OK

3.INSPECT EFI MAIN RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EFI MAIN RELAY
a.
A167865N13
1.99,0.646 1.531,0.292 true 2.656,0.635 3.063,0.26 true 2.531,1.125 3.063,1.125 true 2.531,1.625 3.073,1.625 true 1.208,0.75 1.521,1.104 0.313,0.354 10 5 0.208,0.75 0.594,1.031 0.385,0.281 10 3 1.219,1.313 1.573,1.667 0.354,0.354 10 2 0.198,1.302 0.583,1.615 0.385,0.313 10 1 1.417,0.198 1.708,0.417 0.292,0.219 10 1 3.104,0.167 3.406,0.458 0.302,0.292 10 2 3.125,1.552 3.427,1.771 0.302,0.219 10 3 3.125,1.042 3.427,1.323 0.302,0.281 10 5

Remove the EFI MAIN relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)

NG

REPLACE EFI MAIN RELAY

4.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - ECM)
a.

Remove the EFI MAIN relay from the instrument panel junction block.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
EFI MAIN relay (5) - C23-7 (+B1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
EFI MAIN relay (5) or C23-7 (+B1) - Body ground Always 10 kΩor higher



d.

Reconnect the ECM connectors.


e.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - BODY GROUND)
a.

Remove the EFI MAIN relay from the instrument panel junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN relay (1) - Body ground Always Below 1 Ω



c.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY VOLTAGE)
a.
A261741C02
0.729,0.042 1.083,0.406 0.354,0.365 10 *a 2.104,0.625 2.458,1.031 0.354,0.406 10 *1
*1 Fuse Block
*a EFI Relay Terminal


Remove the EFI MAIN relay from the instrument panel junction block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
EFI MAIN relay (3) - Body ground Ignition switch ON 11 to 14 V



d.

Reinstall the EFI MAIN relay.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - EFI MAIN RELAY)
a.

Disconnect the ignition switch connector.


b.

Remove the EFI MAIN relay from the instrument panel junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E28-6 (IG2) - EFI MAIN relay (2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E28-6 (IG2) or EFI MAIN relay (2) - Body ground Always 10 kΩor higher



d.

Reinstall the EFI MAIN relay.


e.

Reconnect the ignition switch connector.

Result:
Proceed to
OK
NG




OK

8.INSPECT IGNITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH

OK

CHECK AND REPAIR HARNESS OR CONNECTOR (IGNITION SWITCH - POSITIVE BATTERY TERMINAL)

NG