Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM J

K3-VE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B1 (BAT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A263585E04
4.906,0.51 5.469,0.833 0.563,0.323 10 ECM 1.625,1.115 2.719,1.479 1.094,0.365 10 From EFI Fuse 1.198,1.458 3.229,1.875 2.031,0.417 10 From EFI MAIN Relay 0.531,2.229 2.958,2.823 2.427,0.594 10 Throttle Position Sensor, Manifold Absolute Pressure Sensor (Sensor which have IC) 0.333,2.885 2.938,3.531 2.604,0.646 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 2.927,0.99 3.563,1.333 0.635,0.344 10 BAT 2.927,1.354 3.552,1.719 0.625,0.365 10 +B1 2.896,2.229 3.802,2.625 0.906,0.396 10 VC, VCPM 4.417,1.167 6.406,1.615 1.99,0.448 10 5V Constant Voltage Circuit 5.354,2.042 6.552,2.542 1.198,0.5 10 Microprocessor 4.083,3.135 4.594,3.448 0.51,0.313 10 R

When the VC (VCPM) circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A266595E03
2.615,1.75 2.927,2.031 0.313,0.281 10 2 2.615,1.302 2.896,1.573 0.281,0.271 10 3 2.615,0.833 2.875,1.073 0.26,0.24 10 1 2.604,4.271 3.083,4.646 0.479,0.375 10 1 2.604,3.75 2.958,4.042 0.354,0.292 10 2 2.604,3.219 3.104,3.479 0.5,0.26 10 3 4.76,0.854 5.073,1.125 0.313,0.271 10 16 4.76,1.302 5.094,1.615 0.333,0.313 10 23 4.76,1.74 5.125,2.083 0.365,0.344 10 33 4.76,3.208 5.167,3.552 0.406,0.344 10 17 4.76,3.74 5.188,4.063 0.427,0.323 10 12 4.76,4.271 5.198,4.656 0.438,0.385 10 35 5.063,0.844 5.635,1.229 0.573,0.385 10 VC 5.063,1.396 5.792,1.844 0.729,0.448 10 VTHO 5.063,1.75 5.656,2.156 0.594,0.406 10 E2 2.281,0.969 2.802,1.375 0.521,0.406 10 VC 2.146,1.385 2.708,1.698 0.563,0.313 10 PSW 2.396,1.833 2.781,2.281 0.385,0.448 10 - 2.292,3.333 2.719,3.604 0.427,0.271 10 VC 2.24,3.854 2.76,4.167 0.521,0.313 10 PIM 2.396,4.354 2.802,4.698 0.406,0.344 10 - 5.063,3.219 5.771,3.625 0.708,0.406 10 VCPM 5.063,3.844 5.698,4.135 0.635,0.292 10 PIM 5.063,4.271 5.771,4.625 0.708,0.354 10 E2PM 0.167,5.052 3.281,5.51 3.115,0.458 10 MANIFOLD ABSOLUTE PRESSURE SENSOR 0.156,4.885 0.656,5.208 0.5,0.323 10 C11 0.542,2.354 2.917,2.958 2.375,0.604 10 THROTTLE POSITION SENSOR 0.552,2.188 1.01,2.448 0.458,0.26 10 C12 5.635,5.229 6.469,5.615 0.833,0.385 10 ECM 5.635,5.063 6.313,5.417 0.677,0.354 10 C24

PROCEDURE

1.CHECK MIL
a.

Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.

Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



d.

Reconnect the throttle position sensor connector.



A

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



d.

Reconnect the manifold absolute pressure sensor connector.



A

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C24-16 (VC) - Body ground Always 10 kΩ or higher
C24-17 (VCPM) - Body ground Always



e.

Reconnect the throttle position sensor connector.


f.

Reconnect the manifold absolute pressure sensor connector.


g.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C