Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › IGNITION SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014986 IGNITION SYSTEM G

3SZ-VE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 19500 1.INSPECT IGNITION COIL AND PERFORM SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/o Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR).

Powertrain > Engine > Clear DTCs
50002 206
HINT:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Check whether spark occurs.

i.

Remove the 4 ignition coils and 4 spark plugs (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL).


ii.
A266672

Disconnect the 4 injector connectors.


iii.
A261422

Install a spark plug to each ignition coil and connect the ignition coil connectors.


iv.

Ground the spark plugs.


v.

Check that spark occurs while the engine is being cranked.

NOTICE:
·

Ground the spark plugs when checking them.

·

Replace any ignition coils that have been subjected to a physical impact.

·

Do not crank the engine for more than 2 seconds.



If spark does not occur, perform the following procedure.



c.

Perform the spark test in accordance with the following procedure.

i.

Check that the wire harness side connector of the ignition coil with igniter is securely connected.

Result
Result Proceed to
NG Connect securely
OK Go to next step


ii.

Perform a spark test on each ignition coil with igniter.

1.

Replace the ignition coil with igniter with a normally functioning one.

2.

Perform the spark test again.


Result
Result Proceed to
OK Replace ignition coil with igniter
NG Go to next step


iii.

Perform a spark test on each spark plug.

1.

Replace the spark plug with a normally functioning one.

2.

Perform the spark test again.


Result
Result Proceed to
OK Replace spark plug
NG Go to next step


iv.
A207834C02
2.406,1.677 2.094,1.208 true 1.083,1.677 1.396,1.208 true 0.125,0.094 0.719,0.51 0.594,0.417 10 *a 0.99,1.719 1.354,1.958 0.365,0.24 10 + 2.427,1.719 2.865,2.01 0.438,0.292 10 -
*a Front view of wire harness connector
(to Ignition Coil)


Check that power is supplied to the ignition coil with igniter.

1.

Turn the ignition switch to ON.

2.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
1 (+) - 4 (-) Ignition switch ON 11 to 14 V


Result
Result Proceed to
NG Check wiring between ignition switch and ignition coil with igniter and check ground circuit
OK Replace the ECM



d.

Connect the 4 injector connectors.


e.

Install the 4 ignition coils and 4 spark plugs (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION).


Hide 19100P 2.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



a.

Check the electrode.

i.
I039522C02
2.135,0.396 2.292,0.49 0.156,0.094 2.25,1.031 2.563,1.188 0.313,0.156 0.594,1.938 1.094,1.938 false 0.427,1.865 0.875,2.156 0.448,0.292 10 *1
*1 Body Ground


Measure the insulation resistance.

Standard Resistance:

10 MΩ or more


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.
B001301

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO SXU22PR9
NGK DCPR7EA-9



d.
A193077C04
0.615,1.375 1.073,1.698 0.458,0.323 10 *a
*a Electrode Gap


Using a spark plug gap gauge, measure the electrode gap.

Electrode gap:

0.8 to 0.9 mm (0.032 to 0.035 in.)


Maximum electrode gap:

1.1 mm (0.043 in.)


If the gap is greater than the maximum, replace the spark plug.