Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  U0001  High Speed CAN Communication Bus  U0101  Lost Communication with TCM  U0156  Lost Communication with Instrument Panel Cluster Control Module (Combination Meter)  


DESCRIPTION

The ECM intercommunicates with the TCM and the combination meter assembly through the Controller Area Network (CAN).

If the ECM cannot communicate with the TCM and/or the combination meter assembly, the ECM sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0001 High Speed CAN Communication Bus No communication between ECM, combination meter and TCM for 2 second or more
(1 trip detection logic)
·

Open or short in TCM, ECM and combination meter circuit

·

TCM

·

Combination meter assembly

·

ECM


Comes on DTC stored
U0101 Lost Communication with TCM Either of following condition met:
(1 trip detection logic)
·

No communication from TCM (reception) for 1 second or more

·

No communication from ECM (transmission) for 0.3 seconds or more


·

Open or short in TCM and ECM circuit

·

TCM

·

ECM


Comes on DTC stored
U0156 Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) No communication from combination meter (reception) for 1 second or more
(1 trip detection logic)
·

Open or short in combination meter and ECM circuit

·

Combination meter assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A264080E06
5.302,2.656 6.083,3.052 0.781,0.396 10 ECM 4.979,1.219 5.688,1.635 0.708,0.417 10 CANH 1.448,1.219 2.208,1.646 0.76,0.427 10 CANH 4.979,1.969 5.781,2.365 0.802,0.396 10 CANL 1.458,1.969 2.302,2.323 0.844,0.354 10 CANL 0.635,2.667 2.375,3.125 1.74,0.458 10 COMBINATION METER ASSEMBLY 0.135,0.073 3.156,0.448 3.021,0.375 12 for Manual Transmission w/ ABS: 0.76,3.438 2.823,3.771 2.063,0.333 10 :CAN Communication Line

A266543E02
5.302,1.75 5.792,2.115 0.49,0.365 10 ECM 4.979,0.76 5.635,1.104 0.656,0.344 10 CANH 1.448,0.781 2.083,1.052 0.635,0.271 10 CANH 4.979,1.25 5.615,1.594 0.635,0.344 10 CANL 4.979,2.427 5.625,2.74 0.646,0.313 10 CANH 4.99,2.906 5.594,3.198 0.604,0.292 10 CANL 1.458,1.26 2.156,1.604 0.698,0.344 10 CANL 1.25,1.771 1.667,2.073 0.417,0.302 10 TCM 0.135,0.104 3.156,0.479 3.021,0.375 12 for Automatic Transmission: 0.76,3.427 2.781,3.74 2.021,0.313 10 :CAN Communication Line 4.292,3.406 6.917,3.771 2.625,0.365 10 COMBINATION METER ASSEMBLY*1 4.438,2.281 4.885,2.479 0.448,0.198 10 *1 4.438,2.75 4.885,2.948 0.448,0.198 10 *1 0.24,3.104 2.49,3.521 2.25,0.417 10 *1: w/ Multi Information Display

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/o Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 206

e.

Start the engine.


f.

Drive the vehicle.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 206

h.

Read the DTCs.

Result:
Result Proceed to
U0001, U0101 or U0156 A
No output B




A

B