Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM Y

NETWORKING  CAN COMMUNICATION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

PRECAUTIONS WHEN TROUBLESHOOTING


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

·

If the CAN communication system is malfunctioning, check the contact pressure of the terminals in connectors, as insufficient terminal contact pressure may be the cause.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Refer to Diagnosis System for the DTCs for the CAN communication.

·

Refer to troubleshooting of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



a.

CAN communication DTCs are output for CAN main bus and CAN branch malfunctions as well as for internal malfunctions or power source malfunctions of ECUs for systems using CAN communication. Therefore, when DTCs for internal malfunctions or power source malfunctions of corresponding systems are output at the same time as CAN communication DTCs, troubleshoot according to the internal malfunction and power source malfunction DTCs.


b.

The DLC3 branch and V bus main bus circuits can be checked for malfunctions by inspecting at the DLC3 terminals using an electrical tester.

NOTICE:
·

When inspecting at the DLC3 connector, do not connect the tester directly to the terminals. Instead, connect using service wire.

·

Inspections for an open in an ECU branch wires cannot be performed from the DLC3.




c.

An open in a branch for ECUs that are connected to the CAN main bus can be checked by performing a CAN bus check using the intelligent tester or Techstream. (This inspection is possible when the DLC3 branch and V bus main bus lines are normal.)


d.

If the V bus had a communication error, the probable ECU for which communication stopped can be determined using the combination of communication DTCs (DTCs that start with U) that are output.


e.

When an open circuit is detected, before disconnecting related connectors for inspection, push in the connector body to check that the connector is not loose or disconnected.


f.

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
HINT:
·

If the ignition switch can be turned to ON when the vehicle is brought in for repair, check for DTCs and check the illumination condition of the indicators in the combination meter assembly and the basic operation of the vehicle (such as steering operation) promptly.

·

Do not turn the ignition switch off until the inspection of the vehicle is finished, as some fail-safe functions are canceled when the ignition switch is turned off.

·

If the ignition switch cannot be turned to ON when the vehicle is brought in, measure the voltage of the battery. If the voltage is below 11 V, recharge or replace the battery before performing troubleshooting.

·

If the ignition switch cannot be turned to ON even though the battery voltage is normal, repair this malfunction before performing troubleshooting.

Result:
Proceed to
NEXT





NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Ask the customer if the vehicle is/was equipped with additional devices such as a theft deterrent device or monitor. (If equipped, explain the customer that the additional devices will be removed before performing troubleshooting as the malfunction cannot be checked properly.)



a.

It is useful to confirm the symptoms and the conditions in which the vehicle was operating at the time when a malfunction occurred. This helps to narrow down the malfunctioning part.

HINT:
·

What was affected (system, part or meter warning indicators)

·

What happened (details of the malfunction)

·

When (occurrence date and time, frequency and if it recurs or not)

·

under what kind of situation did the problem occur (driving and operating condition at the occurrence and weather)

·

Road type or condition (city, suburb, paved road, unpaved road, highway, etc.)

·

Return conditions (what made the vehicle return to normal. Example: ignition switch was turned off)


Points to be confirmed
Symptom
·

Multi-information display items

·

Whether the update of multi-information display items stopped

·

Whether the numeric part of drivable distance was not displayed


·

Operation of other systems of concern


Meter warning lights
·

Illumination of warning lights and the order in which they illuminated

·

CHECK ENGINE (MIL)


·

Needle movement

·

Tachometer

·

Speedometer

·

Fuel economy meter


·

Content displayed on the multi-information display




Result:
Proceed to
NEXT




NEXT

3.CHECK INTELLIGENT TESTER OR TECHSTREAM OPERATION
3.CHECK INTELLIGENT TESTER OR TECHSTREAM OPERATION
HINT:

Read the intelligent tester or Techstream operators manual before use.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION.


a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Check that the intelligent tester or Techstream and ECUs can communicate with the ignition switch ON.

HINT:
·

If communication is impossible, the intelligent tester or Techstream screen will indicate an error.

·

If communication between the intelligent tester or Techstream and ECUs is impossible, either the intelligent tester or vehicle has a malfunction.

·

When communication between the intelligent tester and the vehicle is impossible, but communication is possible when the intelligent tester or Techstream is connected to another vehicle, the vehicle has the malfunction. Inspect the CANH and CANL branch lines of DLC3 and ECU power source circuits (in this case perform steps 7 to 9 first). In addition, check that the +B terminal of the DLC3 receives battery voltage (11 V or more).

·

If communication between the intelligent tester or Techstream and ECUs is still impossible even when the intelligent tester or Techstream is connected to another vehicle, the intelligent tester or Techstream has a malfunction. Perform the self tests described in the intelligent tester or Techstream operators manual. (The intelligent tester or Techstream may be malfunctioning or its battery may be discharged.)



Result:
Result Proceed to
OK (Communication between the intelligent tester or Techstream and the vehicle is possible.) A
OK (Communication between the intelligent tester or Techstream and the vehicle is impossible but communication is possible when connected to another vehicle.) B
NG (Communication is not possible between the intelligent tester or Techstream and the vehicle, nor between the intelligent tester or Techstream and another vehicle.) C




A

4.CHECK DTC

B

7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)

C

Refer to to intelligent tester or Techstream operator's manual

4.CHECK DTC
a.

Using the intelligent tester or Techstream, perform Health Check to read current and history DTCs and record them.

NOTICE:
·

CAN communication DTCs are output when there is an open or short in any of the communication lines. Any problems with the power source of a corresponding ECU, or problems in the ECU.

·

If a CAN communication line connector is disconnected with the ignition switch ON, the ECUs of the corresponding system and related systems store a DTC.



HINT:
·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in a CAN bus occurs, DTCs of almost all ECUs on the CAN bus may be output (or a message indicating a communication error may be displayed on the intelligent tester or Techstream screen). In this case, check the resistance of the CAN bus (steps 7 to 9) first.

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed on the intelligent tester or Techstream.




b.

Read the freeze frame data using the intelligent tester and record it.

Result:
Proceed to
NEXT




NEXT

5.CHECK COMMUNICATION MALFUNCTION CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)
5.CHECK COMMUNICATION MALFUNCTION CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)
a.

Select "Communication Malfunction Check" from the screen on the intelligent tester or Techstream.


b.

Record all the DTCs stored for ECUs.

Result:
Proceed to
NEXT




NEXT

6.CHECK CAN BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)
6.CHECK CAN BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Select "CAN Bus Check" from the screen on the intelligent tester or Techstream.


c.

Observe the screen for approximately 2 minutes to check the ECUs displayed on the screen.

Result:
Proceed to
NEXT




NEXT

7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)
7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
E231257C07
1.448,0.26 1.938,0.552 0.49,0.292 2.24,0.458 1.99,0.917 true 1.906,1.49 1.656,1.938 true 0.104,0.094 0.563,0.521 0.458,0.427 10 *a 2.323,0.385 2.958,0.76 0.635,0.375 10 CANH 1.271,1.875 1.865,2.135 0.594,0.26 10 CANL 1.573,0.313 2.125,0.74 0.552,0.427 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Result Proceed to
OK (54 to 69 Ω) A
NG (70 Ω or higher) B
NG (Below 54 Ω) C




A

8.CHECK FOR SHORT TO GND IN V BUS (CANH, CANL - E)

B

C

8.CHECK FOR SHORT TO GND IN V BUS (CANH, CANL - E)
a.
E231257C08
1.448,0.26 1.938,0.552 0.49,0.292 2.24,0.458 1.99,0.917 true 1.906,1.49 1.656,1.938 true 1.542,0.917 1.24,0.5 true 0.104,0.094 0.563,0.521 0.458,0.427 10 *a 2.323,0.385 2.958,0.76 0.635,0.375 10 CANH 1.271,1.875 1.865,2.135 0.594,0.26 10 CANL 1.573,0.313 2.125,0.74 0.552,0.427 10 E12 1.073,0.396 1.708,0.771 0.635,0.375 10 E
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E12-14 (CANL) - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Result:
Proceed to
OK
NG




OK

9.CHECK FOR SHORT TO +B IN V BUS (CANH, CANL - +B)

NG

9.CHECK FOR SHORT TO +B IN V BUS (CANH, CANL - +B)
a.
E231257C09
1.448,0.26 1.938,0.552 0.49,0.292 2.24,0.458 1.99,0.917 true 1.906,1.49 1.656,1.938 true 2.656,1.885 2.354,1.469 true 0.104,0.094 0.563,0.521 0.458,0.427 10 *a 2.323,0.385 2.958,0.76 0.635,0.375 10 CANH 1.271,1.854 1.865,2.115 0.594,0.26 10 CANL 1.573,0.313 2.125,0.74 0.552,0.427 10 E12 2.719,1.823 3.313,2.083 0.594,0.26 10 +B
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E12-14 (CANL) - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG




OK

10.CHECK RESULT OF CAN BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)

NG

10.CHECK RESULT OF CAN BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER OR TECHSTREAM)
a.

Inspect or repair the probable malfunctioning part based on the check result of step 6 (the step in which CAN Bus Check was performed).

Result of CAN Bus Check (Connection Status Check Using Intelligent Tester or Techstream):
Result Proceed to
All ECUs connected to the CAN communication system are displayed on the screen.
(CAN bus circuit is currently normal.)
A
One of the ECUs connected to the V Bus is not displayed on the screen.
(Open in ECU branch lines, or communication interrupted.)
B
In addition to ECUs which are connected to the CAN communication system but are not displayed on the screen, there are ECUs for which the detection status changes (changes between detected and not detected) during the inspection.
(Open in one side of ECU branch lines.)
C


NOTICE:
·

Non-installed ECUs will not be displayed. Do not mistake them for being in communication stop mode.

·

It may be possible to select buses that do not have ECUs from the bus selection pull-down menu on the intelligent tester or Techstream. This is not a malfunction.



HINT:
·

Regarding CAN Bus Check, refer to How to Interpret CAN Bus Diagnosis (CAN Bus Check) Screen.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the detection status of ECUs changes during the inspection, one of the branch lines of a connected ECU may be open. (Signals from the ECU that has an open in one of its branch lines create electrical noise, affecting response to the intelligent tester or Techstream and whether or not the ECUs displayed.)





A

11.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)

B

C

11.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)
a.

Select "Bus Check" from "System Select".


b.

Write down all of the DTCs output from each ECU.

HINT:
·

If communication DTCs are stored, and all ECUs connected to the CAN communication system are displayed on the Communication Bus Check (CAN bus check) screen of the intelligent tester or Techstream, a past malfunction that is currently not occurring is suspected.

·

When a CAN branch of the V bus is malfunctioning, because the ECUs related to it detect the malfunction, the problem area can be determined using the combination of DTCs that are output.



Result:
Proceed to
NEXT




NEXT

12.DTC COMBINATION TABLE
12.DTC COMBINATION TABLE
a.

Confirm the problem according to the combination of output DTCs regarding the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
Combination of DTCs is not in DTC Combination Table A
Combination of DTCs is in DTC Combination Table B


HINT:

CAN communication system history DTCs may indicate the problem if CAN communication system DTCs are output and all ECUs connected to the CAN communication system are displayed on "CAN Bus Check" of the intelligent tester or Techstream.




A

13.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS OF V BUS)

B

13.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS OF V BUS)
a.

Connect the cable to the negative (-) battery terminal.


b.

Clear the DTCs using the intelligent tester or Techstream.


c.

Perform the tests in Symptom Simulation to check the wire harnesses and connectors including those for V bus main bus lines.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


d.

Based on the results of the check, inspect the parts that output DTCs to determine the malfunctioning part.

HINT:

If DTCs are output, do not turn the ignition switch off.


Result:
Proceed to
NEXT




NEXT

14.REPAIR OR REPLACEMENT
14.REPAIR OR REPLACEMENT
Result:
Proceed to
NEXT



NEXT

15.CONFIRMATION TEST*
15.CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END