Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used. The HO2 sensor is located behind TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor indicates to the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V). Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor indicates to the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level. The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E29
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 true 2.583,2.417 3.24,2.385 true 2.677,2.719 3.26,2.854 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.656 3.302,1.281 3.302,1.281 2.667,1.5 true 1.448,0.813 2.594,1.135 1.146,0.323 10 Atmospheric Air 3.344,0.74 4.083,0.938 0.74,0.198 10 Housing 3.344,1.208 4.76,1.479 1.417,0.271 10 Platinum Electrode 3.958,0.906 4.948,1.188 0.99,0.281 10 Output Voltage 5.01,0.99 6.406,1.323 1.396,0.333 10 Ideal Air-fuel Mixture 2.01,3.167 2.948,3.5 0.938,0.333 10 Exhaust Gas 3.344,1.698 4.688,2.146 1.344,0.448 10 Solid Electrolyte (Zirconia Element) 3.302,2.792 4.521,3.188 1.219,0.396 10 Coating (Ceramic) 3.323,2.313 3.854,2.615 0.531,0.302 10 Heater 1.365,2.833 1.885,3.167 0.521,0.333 10 Cover 4.792,2.896 7.042,3.281 2.25,0.385 10 Richer - Air-fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) Following conditions (a) and (b) met after engine warmed up (2 trip detection logic):

(a) Fuel-cut executed after vehicle driven under specified vehicle load or more

(b) Heated oxygen sensor output remains more than 0.6 V


Following conditions (a) and (b) met after engine warmed up (2 trip detection logic):

(a) Vehicle driven under specified vehicle load or more for 30 seconds or more

(b) Heated oxygen sensor output remains less than 0.1 V for 10 seconds or more, or no rich signal input to ECM


·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A149570E03
4.76,0.781 5.177,0.354 false 2.802,0.25 3.573,0.677 0.771,0.427 10 40 seconds or more 2.177,2.146 2.865,2.417 0.688,0.271 10 Warm Up 0.896,0.469 1.896,0.771 1,0.302 10 Vehicle Speed 0.354,0.99 1.563,1.219 1.208,0.229 10 70 km/h (43 mph) 0.552,1.854 1.885,2.073 1.333,0.219 10 Ignition Switch OFF 4.969,1.948 5.521,2.271 0.552,0.323 10 Time 0.354,1.167 1.896,1.365 1.542,0.198 10 with 2,000 rpm or more 3.948,0.25 4.698,0.646 0.75,0.396 10 10 seconds or more 5.25,0.26 6.531,0.677 1.281,0.417 10 20 seconds or more with Fuel-Cut 2.323,1.583 2.573,1.813 0.25,0.229 10 (f) 4.354,1.167 4.646,1.396 0.292,0.229 10 (h) 3.073,1.167 3.385,1.438 0.313,0.271 10 (g)

HINT:

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.


(a) Connect the intelligent tester or Techstream to the DLC3.

(b) Turn the ignition switch to ON and turn the intelligent tester or Techstream on.

(d) Enter the following menus: Powertrain / Engine / Data List / O2S (A/FS) Monitor.

(e) Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).

(f) Start the engine and warm it up.

(g) Drive the vehicle at a vehicle speed of more than 70 km/h (43 mph) for 40 seconds or more.

(h) Drive the vehicle at a vehicle speed of more than 70 km/h (43 mph) for 10 seconds or more, then decelerate the vehicle (accelerator pedal fully released) for 20 seconds or more to perform fuel-cut operation.

(i) Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 sensor monitor operates.

(j) Enter the following menus: Powertrain / Engine / DTC and check if any DTCs (any pending DTCs) are set.


Powertrain > Engine > Clear DTCs
50002 206
Powertrain > Engine > Data List
Tester Display
O2S(A/FS) Monitor CMPL
50003 206 19
Powertrain > Engine > Trouble Codes
50001 206
HINT:
·

The MIL is illuminated during step (g) or (h) if a malfunction still exists.

·

If the item O2S (A/FS) Monitor does not change to Compl (Complete), and any pending DTCs fail to set, extend the driving time.



NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


CAUTION / NOTICE / HINT

·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0136)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0136 A
P0136 and other DTCs B


HINT:

If any DTCs other than P0136 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 2))

B

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 2))
a.
A149559E03
0.375,1.073 0.792,1.417 0.417,0.344 10 1 V 0.396,2.604 0.885,2.99 0.49,0.385 10 0 V 2.875,2.677 3.427,3 0.552,0.323 10 Time 0.073,0.229 2.25,0.604 2.177,0.375 10 Heated Oxygen Sensor Output 0.042,1.74 0.708,2.063 0.667,0.323 10 0.4 V 0.031,1.865 0.823,2.219 0.792,0.354 10 or more

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / O2S B1 S2.

Powertrain > Engine > Data List
Tester Display
O2S B1 S2
50003 206 39

e.

Warm up the engine.


f.

Allow the engine to run at 2,500 rpm for 90 seconds.


g.

Depress the accelerator pedal quickly until the engine rpm reaches 4,000 rpm 3 times.

Standard voltage:

Fluctuates with an amplitude of 0.4 V or more.


Result:
Proceed to
OK
NG




OK

3.PERFORM CONFIRMATION DRIVING PATTERN

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
3.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Clear all DTCs before performing the confirmation driving pattern.


Powertrain > Engine > Clear DTCs
50002 206
Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0136 A
No output B




A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C27-3 (+) - C24-24 (OX2) Always Below 1 Ω
C27-1 (IREL) - C24-13 (OXH2) Always Below 1 Ω
C27-4 (E) - C24-33 (E2) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C27-3 (OX2) - C24-24 (OX2) Always Below 1 Ω
C27-1 (OXH2) - C24-13 (OXH2) Always Below 1 Ω
C27-4 (E2) - C24-33 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C27-3 (+) or C24-24 (OX2) - Body ground Always 10 kΩ or higher
C27-4 (E) or C24-33 (E2) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C27-3 (OX2) or C24-24 (OX2) - Body ground Always 10 kΩ or higher
C27-4 (E2) or C24-33 (E2) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 2) connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR