Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) D

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  DIAGNOSIS SYSTEM  


EURO-OBD (EUROPE)


FI02547

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 14230-4). Various data output from the vehicle's ECM can then be read.

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

1. The emission control system/components

2. The power train control components (which affect vehicle emissions)

3. The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 14230-4 are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

To check DTCs, connect the intelligent tester or Techstream to the Data Link Connector 3 (DLC3) of the vehicle.

The intelligent tester or Techstream displays DTCs, the freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be erased using the tester (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR).


M-OBD (EXCEPT EUROPEAN SPEC.)


FI02547

When troubleshooting a Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the intelligent tester or Techstream. Various data output from the ECM can then be read. OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:

1. The emission control system/components

2. The power train control components (which affect vehicle emissions)

3. The power train control components (which affect vehicle emissions)


2-TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again after the ignition switch is turned to off and then to ON, the MIL illuminates (2nd trip).


DLC3 (Data Link Connector 3)


Check the DLC3 (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION).


BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If voltage is below 11 V, replace or recharge the battery before proceeding.


MIL (Malfunction Indicator Lamp)


a.

The MIL is illuminated when the ignition switch is first turned to ON (the engine is not running).


b.

The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.

HINT:

If the MIL is not illuminated when the ignition switch is first turned to ON, check the MIL circuit (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>MIL Circuit).




READINESS CODE


HINT:
·

With "Readiness Code" you can check whether or not the self-diagnosis system of emission control system has been completed by using the intelligent tester or Techstream.

·

The ECM performs self-diagnosis of individual systems for which specified conditions have been met, and changes the monitor status of the readiness code for each system from "Incmpl" to "Compl".

·

When monitor status becomes "Compl", this status is maintained until DTC is deleted or ECM backup power cuts off.



a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester or Techstream on.


c.

Enter the following menus: Powertrain / Engine/ Data List.

Powertrain > Engine > Data List
Tester Display
Heater Monitor ENA
Heater Monitor CMPL
O2S(A/FS) Monitor ENA
O2S(A/FS) Monitor CMPL
EVAP Monitor ENA
EVAP Monitor CMPL
Catalyst Monitor ENA
Catalyst Monitor CMPL
50003 206 10,18,11,19,14,22,16,24

d.

According to the display on the intelligent tester or Techstream, read the "Readiness Code".

HINT:
·

If the vehicle has a self-diagnosis system, "Avail" is displayed on the monitor of the corresponding system. If the vehicle does not have a self-diagnosis system, "Not Avl" is displayed on the monitor, and monitor status remains set to "Incmpl".

·

Readiness code monitor status is a function that displays "Compl" or "Incmpl" for self-diagnosis for each system. It does not display "normal" or "abnormal", the results of self-diagnosis. (The results of self-diagnosis can be determined according to whether or not DTCs are output).



Tester Display Monitor Status Related DTC Note
Heater Monitor ENA Not Avl / Avail P0135
P0141
-
Heater Monitor CMPL Compl / Incmpl
O2S(A/FS) Monitor ENA Not Avl / Avail P0130
P0133
P0136
-
O2S(A/FS) Monitor CMPL Compl / Incmpl
EVAP Monitor ENA Not Avl / Avail P0443 -
EVAP Monitor CMPL Compl / Incmpl
Catalyst Monitor ENA Not Avl / Avail P0420 -
Catalyst Monitor CMPL Compl / Incmpl