Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) J

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to the ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is first turned to the ON the MIL should be illuminated and should then turn off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure.

WIRING DIAGRAM

A263594E02
0.823,3.833 1.906,4.177 1.083,0.344 10 BATTERY 0.667,2.573 1.635,3.031 0.969,0.458 10 FL MAIN 0.646,1.333 1.219,1.677 0.573,0.344 10 AM2 2.156,1.448 2.76,1.885 0.604,0.438 10 AM2 2.188,1.948 2.677,2.313 0.49,0.365 10 IG2 2.177,3.229 3.031,3.594 0.854,0.365 10 ECU IG2 3.917,3.438 4.385,3.802 0.469,0.365 10 39 3.917,1.74 4.438,2.135 0.521,0.396 10 37 5.958,0.906 6.406,1.313 0.448,0.406 10 W 5.667,0.802 6.167,1.271 0.5,0.469 10 27 2.135,1.198 2.479,1.625 0.344,0.427 10 5 2.135,2.198 2.479,2.573 0.344,0.375 10 6 3.917,1.969 4.521,2.302 0.604,0.333 10 EFI 3.927,3.24 4.469,3.594 0.542,0.354 10 IG 2.573,1.667 3.448,2.302 0.875,0.635 10 IGNITION SWITCH 2.573,1.51 3.104,1.938 0.531,0.427 10 E28 4.427,2.625 6.219,3.333 1.792,0.708 10 COMBINATION METER ASSEMBLY 4.427,2.469 5.073,2.844 0.646,0.375 10 E34 6.313,2.104 6.885,2.573 0.573,0.469 10 ECM 6.313,1.948 6.885,2.302 0.573,0.354 10 E3

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the chart below.

Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Check whether any DTCs have been stored. Note down any DTCs.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 206

e.

f.

Check whether the MIL turns off.

OK:

MIL should turn off.



HINT:

If the system has any malfunctions (the ECM stores any DTCs), troubleshoot those DTCs and repair them first.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
OK
NG



OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A141555C01
2.292,0.604 2.594,0.792 0.302,0.188 2.146,2.167 1.906,2.469 true 1.813,2.5 2.167,2.875 0.354,0.375 10 W 0.156,0.125 0.583,0.521 0.427,0.396 10 *a 2.365,0.615 2.927,0.979 0.563,0.365 10 E3
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)

B

C

4.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
E3-27 (W) or E34-37 (EFI) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter assembly connector.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE COMBINATION METER ASSEMBLY (MIL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check whether the MIL illuminates when turning the ignition switch to ON.

OK:

MIL should illuminate.


Result:
Proceed to
OK
NG




OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: the intelligent tester or Techstream cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER (CHECK MIL CIRCUIT)

B

7.INSPECT COMBINATION METER (CHECK MIL CIRCUIT)
a.

See the combination meter troubleshooting procedure.

Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS OR CONNECTOR (ECM - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY (MIL CIRCUIT)

8.CHECK HARNESS OR CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Check the resistance.

Standard Resistance (Check for Open):
Tester Connections Condition Specified Conditions
E3-27 (W) - E34-37 (EFI) Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter assembly connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C