Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) J

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B1 (BAT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A263585E05
4.906,3.365 5.5,3.698 0.594,0.333 10 ECM 1.625,1.135 2.76,1.521 1.135,0.385 10 From EFI Fuse 1.198,1.479 3.073,1.865 1.875,0.385 10 From EFI MAIN Relay 0.531,2.24 2.646,2.844 2.115,0.604 10 Throttle Position Sensor, Manifold Absolute Pressure Sensor (Sensor which have IC) 0.333,2.896 2.729,3.417 2.396,0.521 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 2.927,1.042 3.385,1.406 0.458,0.365 10 BAT 2.927,1.396 3.365,1.74 0.438,0.344 10 +B1 2.896,2.25 3.781,2.635 0.885,0.385 10 VC, VCPM 4.417,1.177 6.313,1.698 1.896,0.521 10 5V Constant Voltage Circuit 5.354,2.063 6.448,2.542 1.094,0.479 10 Microprocessor 4.073,3.135 4.396,3.458 0.323,0.323 10 R

When the VC (VCPM) circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A266595E02
2.615,1.771 2.99,2.104 0.375,0.333 10 2 2.615,1.302 2.99,1.656 0.375,0.354 10 3 2.615,0.854 3,1.25 0.385,0.396 10 1 2.604,4.292 3.052,4.708 0.448,0.417 10 1 2.604,3.771 2.969,4.135 0.365,0.365 10 2 2.604,3.219 3,3.583 0.396,0.365 10 3 4.76,0.865 5.219,1.198 0.458,0.333 10 16 4.76,1.313 5.177,1.625 0.417,0.313 10 23 4.76,1.75 5.229,2.104 0.469,0.354 10 33 4.76,3.229 5.156,3.542 0.396,0.313 10 17 4.76,3.76 5.219,4.083 0.458,0.323 10 12 4.76,4.281 5.198,4.646 0.438,0.365 10 35 5.063,0.875 5.5,1.208 0.438,0.333 10 VC 5.063,1.385 5.802,1.729 0.74,0.344 10 VTHO 5.063,1.76 5.479,2.094 0.417,0.333 10 E2 2.281,0.958 2.719,1.292 0.438,0.333 10 VC 2.156,1.417 2.729,1.74 0.573,0.323 10 PSW 2.396,1.844 2.865,2.281 0.469,0.438 10 - 2.292,3.323 2.76,3.698 0.469,0.375 10 VC 2.24,3.854 2.76,4.26 0.521,0.406 10 PIM 2.396,4.375 2.854,4.698 0.458,0.323 10 - 5.063,3.229 5.781,3.594 0.719,0.365 10 VCPM 5.063,3.865 5.698,4.229 0.635,0.365 10 PIM 5.063,4.281 5.74,4.708 0.677,0.427 10 E2PM 0.156,5.146 3.552,5.698 3.396,0.552 10 MANIFOLD ABSOLUTE PRESSURE SENSOR 0.156,4.948 0.823,5.26 0.667,0.313 10 C11 0.542,2.396 2.917,2.844 2.375,0.448 10 THROTTLE POSITION SENSOR 0.542,2.198 1.25,2.583 0.708,0.385 10 C12 5.635,5.271 6.26,5.677 0.625,0.406 10 ECM 5.635,5.083 6.25,5.438 0.615,0.354 10 C24

PROCEDURE

1.CHECK MIL
a.

Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER OR TECHSTREAM AND ECM
2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER OR TECHSTREAM AND ECM
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Check the communication between the intelligent tester or Techstream and ECM.

CAN Bus Check
50007
Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



d.

Reconnect the throttle position sensor connector.



A

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



d.

Reconnect the manifold absolute pressure sensor connector.



A

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
C24-16 (VC) - Body ground Always 10 kΩ or higher
C24-17 (VCPM) - Body ground Always



e.

Reconnect the throttle position sensor connector.


f.

Reconnect the manifold absolute pressure sensor connector.


g.

Reconnect the ECM connector.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C